What to do if my Tally Dascom 1125 power does not turn on?
First, check if the mains voltage is correct. Then, ensure the power cord is securely connected to both the printer and the power outlet. Verify the power outlet is functional; if not, try another outlet. Turn the power off, wait a minute, and then turn the printer on again.
Why does my Tally Dascom 1125 Printer jam paper while printing, and how can I fix it?
If your Tally Printer is experiencing paper jams during printing, try the following: First, turn off the printer and carefully remove the jammed paper, clearing any obstructions from the paper path. Next, ensure that the Print Gap lever is correctly set for the thickness of your paper. If you are using continuous forms, verify that both the incoming and outgoing paper stacks are positioned correctly, ensuring the paper feeds straight.
How to troubleshoot a Tally Printer that is on but won't print?
First, check that the Online indicator is lit. If you're using an interface cable, ensure it's securely connected to both the printer and the computer. Also, verify that paper is loaded. Run the printer Status Page to see if printing executes normally; if it does, the issue likely stems from the interface, computer, incorrect printer settings, or software settings. Finally, confirm that the printer driver selected in your software matches the emulation selected on the printer.
What to do if my Tally Printer jams paper while loading?
If your Tally Printer is jamming paper while loading, try these steps: Turn off the printer and remove the jammed paper, clearing any obstructions from the paper path. Ensure the Print Gap lever is set correctly for the paper thickness. Make sure the paper isn't folded, creased, or torn. For continuous forms, ensure the left and right tractors are adjusted so the forms are taut.
Why is my Tally Printer printing erratic or wrong characters?
If your Tally Printer is printing erratically or producing incorrect characters, make sure the interface cable is securely connected to both the printer and the computer. Also, verify that the printer driver selected in your software matches the emulation selected on the printer. Check the length of the interface cable, ensuring it doesn't exceed the maximum length (Parallel & USB: 2 meters, Serial: 15 meters). Finally, try using a different interface cable.
How to fix light or dark printing on my Tally Dascom 1125?
To correct printing that is too light or too dark on your Tally Printer, ensure the ribbon cartridge is properly installed and feeds smoothly. If needed, replace the ribbon. Also, check that the print gap lever is set appropriately for the thickness of your paper.
Why is my Tally Dascom 1125 printing a blank page?
If your Tally Printer is producing blank pages, first ensure that the ribbon cartridge is properly installed. Also, check that the gap lever is set correctly.
How do I remove smears and stains from Tally Dascom 1125 Printer output?
If smears and stains are appearing on your printed pages, ensure that the print gap lever is set correctly for the thickness of your paper. Check the ribbon for wear and replace it if necessary. Inspect the print head for dirt and clean it gently with a soft cloth if needed. In some cases, the print head may need replacement.
What to do if paper cannot be loaded or fed into my Tally Printer?
If paper cannot be loaded or fed into your Tally Printer, first ensure that the paper select lever located on the top right of the printer is set correctly. Also, make sure that the paper covers the paper-out sensor.
How do I fix vertically misaligned printing on my Tally Dascom 1125 Printer?
To fix vertically misaligned (jagged) printing on your Tally Printer, use the printer's vertical alignment function to check the vertical print alignment. If necessary, adjust the print alignment.
Instructions for positioning the printer correctly on a stable surface, ensuring ventilation and access.
Step-by-step guide for installing the printer ribbon cartridge correctly.
Guidance on connecting interface cables (Centronics, Serial, USB) to the printer.
Instructions on how to connect the printer to the power supply, including voltage checks.
Detailed steps for installing the printer driver on Windows operating systems.
How to adjust the print gap lever based on paper thickness for optimal printing.
Procedure to resolve vertical line misalignments in bi-directional printing.
Function to adjust print head pin usage to maintain print quality temporarily.
How to adjust left, top margins, and tear-off position for print output.
Instructions for cleaning the printer housing, platen, and paper rollers.
Solutions for common problems affecting print quality like light/darkness or smears.
Solutions for problems related to paper loading, jamming, and feeding.
General| Type | Dot Matrix Printer |
|---|---|
| Number of Pins | 9 |
| Connectivity | Wired |
| Print Technology | Impact |
| Print Method | Impact |
| Print Width | 80 mm |
| Interface | USB, Parallel, Serial |
| Paper Size | A4, Letter, Custom |
| Noise Level | 55 dB |
| Paper Handling | Manual Feed, Continuous Feed |
To Next Page
