Technics SH-MZ1200 User Manual

RQT7231
7
Connections
Connect the various equipment to the DJ mixer using stereo phono cables, connection cables and appropriate cables (Each sold separately).
When connecting, make sure to turn all equipment power off.
Connection to the XLR terminals
•Open the terminal cover, align the polarities on the XLR plug (not
included) and XLR terminal and insert the plug until it locks.
•To remove the XLR plug, press the knob on the top of the plug
and remove it.
•After removing it, press the center of the terminal cover and close
firmly.
When using a monaural input effector
•Connect to the R/MONO terminal.
•The mixed left (L) and right (R) signal is output to the effector, and the left (L) and right (R) signal from the effector is input.
When listening with headphones
•Turn down the volume using the MONITOR LEVEL control knob before connecting.
•Avoid listening for prolonged periods of time to prevent hearing damage.
Speakers
(Not included)
Monitor amplifier
(Not included)
Speakers
(Not included)
Amplifier
(Not included)
Speakers
(Not included)
Amplifier
(Not included)
Rear panel
Connect when using an amplifier that
has XLR terminals. Terminal polarity is
indicated in the diagram below.
Cold (–)
Hot (+)Ground
Amplifier
(Not included)
(XLR terminal
compatible)
Speakers
(Not included)
Cassette deck (Not included)
Connection
cable
(Not included)
Type:
RCA coaxial
AV Control Receiver
(Not included)
Effector (Not included)
Connect if you want to use an
external effector or sampler etc.
to adjust the sound.
Headphone
(Not included)
Stereo phono cables
White (L)
Red (R)
Output side connections
Type:
6.3 mm
monaural
Front panel
Type:
6.3 mm stereo

Technics SH-MZ1200 Specifications

Input Sensitivity and Impedance

PHONO input sensitivity	2.5 mV
PHONO input impedance	47 kΩ
LINE input sensitivity	250 mV
LINE input impedance	10 kΩ
EFFECT RETURN input sensitivity	250 mV
EFFECT RETURN input impedance	47 kΩ
MIC input sensitivity	0.7 mV
MIC input impedance	1 kΩ

Output Voltage and Impedance

MASTER 1, 2 (RCA) output voltage	1 V
MASTER 1, 2 (RCA) output impedance	600 Ω
MASTER 1 (XLR) output voltage	1 V
MASTER 1 (XLR) output impedance	600 Ω
MONITOR output voltage	1 V
MONITOR output impedance	1 kΩ
REC OUT output voltage	250 mV
REC OUT output impedance	1 kΩ
EFFECT SEND output voltage	250 mV
EFFECT SEND output impedance	1 kΩ
Headphone output power	30 mW
Headphone output impedance	32 Ω

Frequency Response

MASTER 1, 2 frequency response	20 Hz to 20 kHz
REC OUT frequency response	20 Hz to 20 kHz
EFFECT RETURN frequency response	20 Hz to 20 kHz
MIC frequency response	20 Hz to 20 kHz

Digital Audio

Coaxial digital input compatible sampling rate	48 kHz/44.1 kHz/32 kHz
Coaxial digital output sampling rate	44.1 kHz

Equalizer Characteristics

CD/LINE/PHONO LOW EQ gain	+12 dB, –24 dB (50 Hz)
CD/LINE/PHONO MID EQ gain	+12 dB, –24 dB (1 kHz)
CD/LINE/PHONO HIGH EQ gain	+12 dB, –24 dB (10 kHz)
MIC LOW EQ gain	+12 dB, –24 dB (100 Hz)
MIC HIGH EQ gain	+12 dB, –24 dB (10 kHz)

General

Power supply	AC 230-240 V, 50 Hz
Power consumption	35 W
Dimensions (WxHxD)	300 mm x 103 mm x 330 mm
Mass	5.3 kg