Tecsun PL-310 Operation Manual

1. Long press [ALARM] button with a "B" sound. Rotate
the [TUNING] knob when "hour" is flashing in the display.
2. Short press [ALARM] button again with a "BB" sound,
the "minute" flashing. Rotate the [TUNING] knob to
adjust the "minute"
3. Short press [ALARM] button again with another "BB"
sound and notice the alarm's duration is flashing.
Rotate the [TUNING] knob to select 1 ~ 90 minutes of
the alarm's duration.
4. Finally, short press [ALARM] button again with a long
"B--" sound to confirm.
Note: If [ALARM] button not to be pressed again within 3
seconds for confirming time, it will auto confirm the present
display time and following a long "B--" sound.
ALARM SETTING
13
SLEEP
Timer
DELETE MEMORY
SLEEP
Timer
16
Select the alarm by radio " " or by buzzer " "
button with a "B" sound and notice that the " " symbol
shows up in the Timer display section.
2. To activate the alarm by buzzer, short press [ALARM]
button again with a "BB" sound and notice that the " "
symbol appears in the Timer display section.
3. Short press [ALARM] button again with a long "B--" sound
and notice nothing appears in the Timer display section to
turn off the alarm.
Set the alarm by radio
1. Turn on the radio, tune into your favorite alarm radio
station. Please set the volume at the noticeable level.
2. Short press [M] button with a "B" sound.
3. Short press [ALARM] button with a "B" sound and notice
" " symbol is flashing for couple seconds. Now this
alarm radio station is set.
It will go on when the alarm is activated in either the radio
is off, or the radio is on other station.
Alarm by buzzer
1. When the alarm is activated,
"BB" sound will continuously
alarmed. It will turn off
automatically according to
your setting.
2. If the alarm is activated, when
you are listening the radio;
this radio will automatically turn
off, and activate the alarm
(only "BB" sound will come out).
1. To activate the alarm by radio, short press [ALARM]
Delete single memory
flashing
Method 1: Delete memory manually
1. Short press the [SCAN MODE]
button with a "B" sound.
2. Rotate the [TUNING] knob to
the stations that you want to
delete in the memory.
3. Long press the [DELETE] button
with a "B" sound.
4. Short press [DELETE] button
again to confirm with a long
"B- -" sound.
Note: If " " is flashing more than 3 seconds without
confirmation, it will exit the delete function automatically.
Method 2: Semi auto-delete radio stations
1. Short press the [SCAN MODE]
button with a "B" sound.
2. Long press the [SCAN MODE]
button with a "B" sound to
activate the Auto scan memory
function.
3. When it browses & stops into
the unwanted stations, simply
press [DELETE] button with a
long "B--" sound. Afterwards,
it restarts to browse again for
the next radio station.
Select the alarm by radio " " or by buzzer " "
1.To activate the alarm by radio, short press [ALARM]
button with a "B" sound and notice that the " " symbol
shows up in the Timer display section.
2.To activate the alarm by buzzer, short press [ALARM]
button again with a "BB" sound and notice that the " "
symbol appears in the Timer display section.
3.Short press [ALARM] button again with a long "B--" sound
and notice nothing appears in the Timer display section to
turn off the alarm.
Set the alarm by radio
1. Turn on the radio, tune into your favorite alarm radio
station. Please set the volume at the noticeable level.
2. Short press [M] button with a "B" sound.
3. Short press [ALARM] button with a "B" sound and notice
" " symbol is flashing for couple seconds. Now this
alarm radio station is set.

Tecsun PL-310 Specifications

General

Brand	Tecsun
Model	PL-310
Category	Receiver
Language	English