How to fix Tecsun Receiver not turning on?
If your Tecsun Receiver is not turning on, the batteries might be the issue. Try replacing them with new ones. Also, make sure the batteries are installed correctly, paying attention to the '+' and '-' signs. If the power button is locked, press the [ ] button to unlock it.
Why does my Tecsun Receiver auto turn off?
If your Tecsun Receiver turns off automatically while listening, it might be because the batteries are low. Try replacing them. Alternatively, the sleep timer may be activated. In this case, simply turn the radio on again.
Why is AM reception poor on my Tecsun Receiver in the USA?
If you are experiencing poor AM reception in the USA with your Tecsun Receiver, it might be due to the tuning step setting. Since the USA uses a 10kHz tuning step for AM, turn off the radio and repeatedly press and hold the [9/10kHz] button to select 10kHz.
What to do if my Tecsun Receiver is malfunctioning?
If your Tecsun Receiver is malfunctioning, it may be due to interference affecting the computer microchip. Try removing and reloading the battery. If the issue persists, contact your nearest dealer for customer service.
Why is my Tecsun Receiver not storing stations with ATS?
If your Tecsun Receiver isn't storing some stations using ATS, it could be because the frequency of those stations is too weak. Try searching for the station manually. Alternatively, there might be interference nearby; try lowering the antenna or moving to another location.
What to do if my Tecsun Receiver alarm makes noise?
If the Tecsun Receiver makes only noise when the alarm is activated, it could be due to several reasons. First, ensure you have properly preset your alarm station. Second, verify that there is a radio broadcast available at that station in your location. Finally, if you are in an area without a radio station for your preset frequency, consider setting the alarm by buzzer.
Why can my Tecsun Receiver only receive limited FM stations in Japan?
If you can only receive limited FM stations in Japan on your Tecsun Receiver, it's likely because the FM frequency range is set incorrectly. The FM frequency for Japan is 76~90MHz. Turn the radio off and press and hold the [FM SET] button to select the correct FM frequency range.
What to do if there is no sound connecting MP3 to my Tecsun Receiver?
If there is no sound when connecting to an external MP3 player with your Tecsun Receiver, make sure you have pressed the [POWER] button until the “ ” flashes on the display.
Explains the Easy Tuning Mode for automatic station scanning and storage.
Instructions for entering frequencies or memory addresses using the keypad.
Details automatic storage of available stations for bands.
Method for storing stations during auto-browsing.
Step-by-step process to manually cycle through stored stations.
Describes automatically scanning through saved memory stations.
Instructions to directly select a stored station by its number.
How to delete one specific saved station.
Deleting stations while auto-browsing.
Erasing all stored stations for a selected band.
Guide to setting a basic alarm using the buzzer sound.
Instructions for setting alarms using a radio station or MP3.
How to briefly activate the LCD backlight.
How to set the LCD backlight to stay on continuously.
Steps to enable or disable the automatic backlight function.
General| Modes | AM/FM/SW |
|---|---|
| FM Frequency Range | 87-108 MHz |
| Tuning Steps (FM) | 0.1 MHz |
| Tuning Steps (MW) | 9 kHz / 10 kHz |
| Tuning Steps (SW) | 5 kHz |
| Speaker | Yes |
| Display | LCD |
| MP3 Player | Yes |
| Headphone Jack | 3.5 mm |
| Type | Portable Radio Receiver |
| Sensitivity (FM) | 3 uV |
| Sensitivity (AM) | 1 mV/m |
| Output Power | 500 mW |
| Power Supply | 3 x AA batteries or DC |
| Additional Features | Alarm Clock, Sleep Timer |
To Next Page
