How to fix a Tecsun S-2000 Receiver that won't turn on?
If your Tecsun Receiver doesn't turn on, or the display is dark, the issue might be with the power supply. First, check the power supply cables to ensure they are properly connected. If you're using batteries, make sure they are correctly installed and not discharged. If using AC power, ensure it's properly connected.
Why does my Tecsun S-2000 Receiver turn off by itself?
If your Tecsun Receiver automatically shuts off while you're listening, there could be several reasons. First, discharged batteries may cause this issue, so check or reinstall them. It's also possible that the alarm was activated by radio; if so, simply turn the radio on again. Finally, the sleep timer might be set, so turning the radio back on will resolve this.
Why is there no stereo sound on my Tecsun S-2000 Receiver with earphones?
If you're experiencing no stereo sound when using earphones with your Tecsun Receiver, the FM signal might be too weak. Try adjusting the antenna's direction and length, or consider using an external antenna. Also, check if the FM ST. setting is set to MONO; if so, change it to stereo. Keep in mind that the broadcast itself might be in MONO.
What to do if my Tecsun S-2000 Receiver alarm only plays noise?
If you are getting only noises when the alarm goes off on your Tecsun Receiver, it could be due to a station not being stored in TIMER A or TIMER B, or the selected station might be asleep. To resolve this, store a station into TIMER A or TIMER B.
Why does my Tecsun S-2000 have no reception with an external antenna?
If your Tecsun Receiver isn't receiving anything when using an external antenna, the antenna selection switch may be set to INT. ANT. Switch it to the EXT. ANT. position.
Why does my Tecsun S-2000 keep turning off by itself?
If your Tecsun Receiver turns off while you're listening, it could be due to several reasons. It might be that the batteries are discharged, so check or reinstall them. Alternatively, the alarm might have been activated, in which case you should turn the radio on again. Also, the sleep timer might be over, so turning the radio on again should solve this.
What to do if Tecsun S-2000 Receiver has noises or stores nothing into memory when ATS?
If you're only hearing noise or nothing is being stored in the memory when using ATS on your Tecsun Receiver, the signal might be too weak, or there could be strong interference nearby. Try manually tuning or directly keying in the frequency. Alternatively, use the ANT.ATT or shorten the telescope antenna before using ATS.
How to fix no stereo sound on Tecsun S-2000 Receiver with earphones?
If you're not getting stereo sound when using earphones with your Tecsun Receiver, it could be due to a few reasons. The FM signal might be too weak, so try adjusting the antenna's direction and length, or consider using an external antenna. Also, check if the FM ST. setting is set to MONO; if it is, change it to stereo. Finally, the broadcast itself might be in MONO.
Why is my Tecsun S-2000 making noises during ATS?
If your Tecsun Receiver is not storing anything into memory or making noises during ATS (Auto Tuning Storage), the signal might be too weak. Try manually tuning or directly keying in the frequency. Alternatively, strong interference nearby could be the cause. In this case, use the ANT.ATT or shorten the telescope antenna, then run ATS again.
What to do if my Tecsun S-2000 has no function?
If your Tecsun Receiver is not working, the MCU might be in an accident. To fix this, use the RESET button to reboot the unit.
Covers power, light, time setting, alarms, sleep, and reset functions for initial operation.
Details antenna, attenuation, gain, squelch, tuning knob, bandwidth, and radio modes.
Instructions for storing and deleting radio station frequencies into memory.
Instructions for setting up two independent programmable alarm timers.
Covers tuning knob, button tuning, and direct frequency entry.
Details on how to delete single memories or entire memory pages.
Instructions for inserting and checking the battery power indicator.
Guidance on connecting the radio using the 220V AC power cord.
Instructions for connecting the radio using a DC adapter.
Using the tuning knob with fast/slow steps for station selection.
Using UP/DOWN buttons for tuning and engaging auto tuning.
Entering desired radio frequencies directly via the keypad.
How to delete a single stored station from memory.
Instructions for deleting an entire page of stored memories.
Detailed steps for adjusting the 24-hour clock display.
Steps for configuring the two independent alarm timers.
How to tune and listen to SSB signals using the BFO control.
Specifications for frequency coverage and reception sensitivity across bands.
Details on selectivity, FM stereo crosstalk, and signal-to-noise ratios.
Specifications for power supply, standby, and dynamic current consumption.
General| IF bandwidth | AM: 6 kHz, SSB: 2.3 kHz |
|---|---|
| Power Supply | DC 12V |
| Modes | AM, FM, SSB |
| FM Tuning Range | 76 - 108 MHz |
| Antenna | External antenna jack, telescopic antenna |
| SSB | Supported |
To Next Page
