To Next Page
G
Gina HarrisAug 27, 2025
Why is the distance reading inaccurate on my Toro Paint Sprayer?
- DDustin WeberAug 27, 2025
If the distance measurement is inaccurate on your Toro Paint Sprayer, calibrate the speed sensor.
Why is the distance reading inaccurate on my Toro Paint Sprayer?
If the distance measurement is inaccurate on your Toro Paint Sprayer, calibrate the speed sensor.
What to do if Toro Paint Sprayer displayed measurements do not make sense?
If the displayed measurements on your Toro Paint Sprayer do not make sense, check the Units of Measurement to ensure that it is set correctly because the Units of Measurement is set to a system other than what you expect.
Why is the Area inaccurate on my Toro 41106 Paint Sprayer?
If the Area on your Toro Paint Sprayer is inaccurate, check and set the appropriate Width in the calibration mode, because the sprayer width might not be correctly entered. Also, calibrate the speed sensor if it is not calibrated correctly. If problems continue, contact your Authorized Service Dealer because the speed sensor might be damaged.
Why does the monitor not function on my Toro 41106?
If the monitor on your Toro Paint Sprayer does not function, connect the monitor cable if it is loose or disconnected. Contact your Authorized Service Dealer if the monitor or cable is damaged.
Why is the speed on my Toro 41106 Paint Sprayer always 0 or erratic?
If the speed reading is always 0 or erratic on your Toro Paint Sprayer, connect the monitor cable and calibrate the speed sensor.
What causes a pressure drop when turning on a boom on my Toro Paint Sprayer?
A pressure drop when you turn on a boom on your Toro Paint Sprayer may occur because: * The boom bypass valve is improperly adjusted. Adjust the boom bypass valve. * There is an obstruction in the boom valve body. Remove the inlet and outlet connections to the boom valve and remove any obstructions. * A nozzle filter is damaged or clogged. Remove and inspect all nozzles.
Why is the monitor on my Toro 41106 operating erratically?
If the monitor on your Toro Paint Sprayer is erratic in operation, keep two-way radios away from the monitor and its cables.
Why does the starter on my Toro Paint Sprayer not crank?
If the starter of your Toro Paint Sprayer does not crank, there are several possible causes: * The range selector might be in a gear other than Neutral. To solve this, press the brake pedal and move the range selector to the Neutral position. * The electrical connections could be corroded or loose. Check the electrical connections to ensure they have good contact. * A fuse might be blown or loose. Correct or replace the fuse. * The battery might be discharged. Charge or replace the battery. * The safety interlock system might be malfunctioning; contact your Authorized Service Dealer. * There might be a broken starter or starter solenoid; contact your Authorized Service Dealer. * Internal engine components might be seized; contact your Authorized Service Dealer.
What to do if my Toro Sprayer engine cranks but won't start?
If your Toro Sprayer's engine cranks but doesn't start, the fuel tank might be empty; refill it with fresh fuel. Also, the fuel system might contain dirt, water, or stale fuel, requiring you to drain and flush the system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected and replace any damaged or dirty spark plugs.
How to fix a Toro Sprayer engine that starts but doesn't keep running?
If your Toro Sprayer's engine starts but doesn't keep running, the fuel tank vent might be restricted; try replacing the fuel cap. Dirt or water in the fuel system could also be the cause, so drain and flush the system and add fresh fuel. Additionally, check for a clogged fuel filter and replace it if needed. Inspect for blown or loose fuses and correct or replace them. Also, check and tighten any loose wire connections.
General| Max Pressure | 3000 PSI |
|---|---|
| Voltage | 120 V |
| Type | Airless |
| Nozzle Size | 0.015 in |
| Power Source | Electric |
