How to fix a starter that won't crank on my Toro Lawn Mower?
If the starter on your Toro Lawn Mower won't crank, check these items: * Ensure the blade-control switch is disengaged. * Engage the parking brake. * Move the motion-control levers to the NEUTRAL-LOCK position. * Make sure you are sitting in the operator’s seat. * Charge the battery if it's dead. * Check the electrical connections for good contact. * Replace the fuse if it's blown.
Why won't my Toro 74902TE engine start?
If your Toro Lawn Mower engine won't start, starts hard, or fails to keep running, try the following: * Fill the fuel tank. * Open the fuel shutoff valve. * Add oil to the crankcase. * Ensure that the throttle control is midway between the 'SLOW' and 'FAST' positions. * Replace the fuel filter. * Clean or replace the air cleaner element. * Check the seat switch indicator; replace the seat if needed. * Check the electrical connections for good contact; clean the connector terminals thoroughly with electrical contact cleaner, apply dielectric grease, and reconnect. * Clean, adjust, or replace the spark plug. * Check the spark plug wire connection.
What to do if my Toro 74902TE machine vibrates abnormally?
If your Toro Lawn Mower is vibrating abnormally, it could be due to: * Bent or unbalanced cutting blade(s); install new cutting blade(s). * A loose blade mounting bolt; tighten the blade mounting bolt. * Loose engine mounting bolts; tighten the engine mounting bolts. * A loose engine pulley, idler pulley, or blade pulley; tighten the appropriate pulley.
What to do if my Toro 74902TE clutch does not engage?
If the clutch on your Toro Lawn Mower doesn't engage, it could be due to a blown fuse, low voltage supply at the clutch, a damaged coil, inadequate current supply, or a rotor/armature air gap that is too large. To address this, replace the fuse, check the coil resistance, battery charge, charging system, and wiring connections, and replace components if necessary; repair or replace the clutch lead wire or electrical system and clean the connector contacts; remove the shim or replace the clutch.
How to fix an uneven cutting height on my Toro Lawn Mower?
To fix an uneven cutting height on your Toro Lawn Mower, start by sharpening any dull blades or replacing bent ones. Next, level the mower deck from side-to-side and front-to-rear. Clean the underside of the mower deck. Also, ensure the tire pressure is correct. If the blade spindle is bent, contact an Authorized Service Dealer.
How to fix uneven cutting height on Toro Lawn Mower?
To fix an uneven cutting height on your Toro Lawn Mower, start by sharpening any dull blades or installing new ones if bent. Ensure the mower deck is level from side-to-side and front-to-rear. Clean the underside of the mower deck, adjust the tire pressure to the correct level. For a bent blade spindle, contact an Authorized Service Dealer.
What to do if my Toro 74902TE does not drive?
If your Toro Lawn Mower doesn't drive, first check that the bypass valves are closed tight. If not, tighten them. Also, inspect the pump belt for wear, looseness, or breakage and change the belt if needed. Ensure the pump belt is correctly positioned on the pulley. Replace the spring if the idler spring is broken or missing. Finally, verify the hydraulic fluid level; add hydraulic fluid to the reservoirs if it is low, or let it cool down if it is too hot.
What causes abnormal vibrations in my Toro 74902TE?
If your Toro Lawn Mower vibrates abnormally, try the following: 1. Install new cutting blade(s). 2. Tighten the blade mounting bolt. 3. Tighten the engine mounting bolts. 4. Tighten the appropriate pulley.
Why Toro 74902TE blades do not rotate?
If the blades on your Toro Lawn Mower aren't rotating, it could be due to a worn, loose, or broken mower deck belt; in this case, install a new deck belt. Another possibility is that the mower deck belt is off the pulley; reinstall it and check the idler pulley, idler arm, and spring for correct position and function. Also, check the pump drive belt for wear, looseness, or breakage, and adjust the belt tension or install a new belt. Finally, inspect the idler spring and replace it if it's broken or missing.
Why does my Toro 74902TE Lawn Mower not drive?
If your Toro Lawn Mower isn't driving, check if the bypass valves are closed tightly. If not, tighten them. A worn, loose, or broken pump belt can also cause this issue, so replace the belt. If the pump belt is off a pulley, replace the belt. A broken or missing idler spring can prevent driving, so replace the spring. Also, check the hydraulic oil level; if it's low, add hydraulic oil to the reservoirs, or let it cool down if it's too hot.
General| Brand | Toro |
|---|---|
| Model | 74902TE |
| Category | Lawn Mower |
| Language | English |
To Next Page
