Connecting
a~
HDMI®
or
DVI
device
to
the
HDMI
input
-....- .-
-_.~
.
_.
PCIN
....
_
TV
back
panel
Note:
To
ensure that the HOMI or
OVI
device
is
reset
properly, it
is
recommended that you follow these
procedures:
• When
turning
on
your
electronic
components,
turn
on
the TV first,
and
then the
HOMI
or
OVI device.
• When
turning
off
your
electronic
components,
turn
off
the
HDMI
or
DVI
device first,
and
then the TV
[1]
EIA/CEA-861-D
compliance covers
the
transmission
of
uncompressed digital video
with
high-bandwidth
digital
content
protection,
which
is
being
standardized
for
reception
of
high-definition video
signals.
Because
this
is
an
evolving
technology,
it
is
possible
that
some
devices
may
not
operate properly
with
the
TV.
To
connect a DVI device, you will need:
•
one
HOMI-to-OVl
adapter
cable
(HDMI
type A
connector) per OVI device
- For proper operation, the length
of
an HOMI-
to-OVI adapter cable should not exceed
9.8
ft
(3m).
The
recommended length is 6.6
ft
(2m).
•
one
pair
of
standard analog audio cables per DVI
device
- An HOMI-to-OVI
adapter
cable transfers
video only Separate analog audio cables
are required (see illustration).
- See "Setting the
HOMI@
audio
mode"
(I(s)~
page
27).
-
."O
..
loot.
["l1'J
Control
panel
Hi:Ir
...
·
•
CQ
III
Ir[ij
"'-.'"
•
, .
L.]
•
2 •
[&~
~~r
le~
~~,
, .
HOMI
device
To
view the HDMI device video:
Select the
HDMI
I,
HOMI
2,
HOM
I 3
or
HOMI
4
video input
source
on the TV.;:
;:
To
select the video input source, press
INPUT
on the
remote control
(1l'Q'
page 21).
The
HDMl
input on
your
TV
receives digital audio
and uncompressed digital video from an
HDMI
source device,
or
uncompressed digital video from a
DVI (Digital Visual Interface) source device.
This
input is designed to accept
HDCP
(High-
Bandwidth Digital-Content Protection) program
material
in
digital form from
ElA/CEA-861-D-
compliant
l'l
consumer
electronic devices (such as
a set-top box
or
DVD
player with
HDMI
or
DVl
output).
The
HDMI
input can accept and display VGA,
SVGA,
XGA,
WXGA.
SXGA,
480i (60Hz),
480p
(60Hz),
nop
(60Hz), I080i
(60Hz)
and
I080p
(24Hz/60Hz)
signal formats. For detailed signal
specifications, see
page
57.
Supported
Audio
format:
Linear
PCM,
sampling
rate
32/44.
1/48
kHz
Note:
To
connect a
PC
to
the
HOMI
input,
see
page
19.
To
connect
an
HDMI device, you will need:
• one HOMl cable (type A connector) per
HDMI
device
- For proper operation, it
is
recommended that
you use
an
HOMI
cable with
the
HOMI Logo (
HOm.")
-
To
display an 1080i/60Hz signal format, you
will
need
a Category 2 cable. Conventional
HOMI/OVI cable
may
not work
properly
- HOMI cable transfers both video
and
audio.
Separate analog audio cables are
not
required (see illustration).
-
See
"Setting the
HOMf®
audio mode"
(1lE
page
27).
HDMllN-
TV
back
panel
Homl
1
16
To Next Page
Loading...
