Using
CableClear®
digital
noise
reduction
The
CableClear® digital noise reduction feature
allows you to reduce visible interference in your
TV
picture.
This
may be useful when receiving a
broadcast with a weak signal (especially a Cable
channel)
or
playing a noisy video cassette
or
disc.
To
change the CableClear settings:
1 Press
MaU
and open the
Picture
menu, highlight
Noise
Reduction
and press
@.
2
In
the
CableClear
field, select your desired setting.
Note:
• If
the
current
input
is
ANT/CABLE,
VIDEO
1,
or
VIDEO
2,
the
menu
will
display
the
text
"CableClear.
"
The
available
selections
are
Off,
Low, Middle, and High.
•
If
the
current
input
is ColorStream
HD,
HDMI
1,
HDMI2, HDMI3
or
HDMI4,
the
menu
will
display
the
text
"oNR.
"
The
available
selections
are
Off,
Low, Middle, and High. Low, Middle.
and High
will
reduce
the
noise
in
varying
degrees,
from
lowest
to
highest,
respectively
3 To save the new settings, highlight
Done
and
press@.
To revert to the factory defaults, highlight
Reset
and
press@.
Using
MPEG
noise
reduction
The MPEG noise reduction feature allows you to reduce
visible interference caused by MPEG compression.
Choices for MPEG noise reduction are
Off,
Low,
Middle,
and
High.
Off
is
automatically selected when
this feature
is
disabled ("grayed out").
To
select the
MPEG
noise reduction level:
1
MENU
.
Press 0 and open the
Picture
menu.
2 Highlight
Noise
Reduction
and press
@.
3
Press.
or
.... to highlight the
MPEG
Noise
Reduction
field, and then press
.....
or
~
to select
either
Off,
Low,
Middle
or
High.
4 To save the new settings, highlight
Done
and
press@.
To revert to the factory defaults, highlight
Reset
and
press@.
I
52
Using
1
DSDp
PC
Mode
You
can use this function to output clear word image
on the TV screen, when a PC
is
connected to the HOMI
terminal.
Note:
This
function
is available only
for
tOBOp
HoMI
input
signal.
To
turn
on
l080p
PC
mode:
1
MENU
.
Press 0 and open the
Picture
menu.
2 Highlight
Noise
Reduction
and press @.
3
Press.
or
.... to highlight the
1080p
PC
Mode
and then press
.....
or
~
to select
On
and press
@.
To
turn
off
l080p
PC
mode:
Select
Off
in step 3 above.
Using
the
Game
Mode
feature
You
can
use
the Game Mode feature for shorter frame
delays when playing a video game requiring split-second
timing between the on-screen display and input from the
controller (such
as
music creation and high-action games).
This feature
is
more effective for 480i and I080i input
signals.
Note:
To
use
the
Game
Mode
feature,
the
current
video
input must
be
Video
1,
Video
2,
ColorStream
HD,
HDMI1, HDMI2,
HDMI3
or HDMI4.
The
Game
Mode
cannot
be
turned
on
when
any other
video
input is
selected.
To
turn
on Game Mode:
1 Press
MaU
and open the
Picture
menu, highlight
the
Game
Mode.
2 Press
.....
or
~
to select
On.
To
turn
off Game Mode:
Select
Off
in step 2 above, change the video input,
or
turn the
TV
off
and then on again.
Note:
You
can change
the
video input
by
pressing (
INPUT)
on
the remote control
(1&
page 29).
To Next Page
Loading...
