Setting
the
Channel
Tuning
Mode
This
feature allows you to
choose
how
tuning
will be
handled
for
analog
and digital
channels
when
the
TV
is
in
Antenna
mode.
Both
analog
and
digital
channels
can
be
tuned
normally
Standard
Note:
To
use
this
feature,
the
Input Configuration
must be set
to
Antenna
(1&
page 24
).
The
channel
tuning
mode
has three options.
To
tune to a channel or input in Select mode:
1
.
BACK
NEXT
While watching
TV,
press
~
....
or
Ciil
~
to open the
Channel BrowserT\l and surf back to a previous item
or
forward to the next item
in
the list.
In
Select
mode,
when
you
stop
on
an item
in
the
Channel
Browser™,
it
will be highlighted but
you
must
press
~
to
tune
the
TV
to the highlighted
item.
2 Press
~
to tune the
TV
to the highlighted item.
3
EXIT
..
Press 0 to
close
the
Channel
Browser
l
M.
To
set the Channel Tuning Mode:
Note: Digital mode will
be
most useful after
analog channels are shut down
by
the
government
in
2009.
1
From
the
Setup
menu, highlight
Installation
and
press
~.
A new set
of
Installation
menu
icons
will appear.
2
Open
the
Terrestrial
menu,
highlight
Channel
Tuning
Mode,
and
then press
~
to
select
your
desired mode.
Note:
•
The
Channel Options windows as well as
the Channel Browser ANT/CABLE list will be
updated automatically when you change the
mode. Also, the History List will be cleared,
but
the Favorites List will be saved.
• Even
if
the Channel Tuning Mode is set
to
Digital, analog channel 3 will still
be
the
default channel
to
prevent the initial case
where
no
digital channels
have
been
found
in
prior channel scans. (Channel Options will not
have anything listed until
a scan
is
done.)
Digital channels will have priority when
manually entering a channel
number
using the
Channel
Number
(0-9)
on the
remote
control, analog
channels
can
still
be
tuned by
rM
/
l!J,
if
available
Only
digital
channels
can
be
tunedDigital
Auto
(default)
Clearing channels from the History List:
•
Reconfiguring
the
ANT/CABLE
input will
clear
the
History List.
Note: See
page
24
for details on configuring
the antenna input.
• Once
32
channels
or
inputs are stored
in
the History
List, the oldest item will be removed from the Jist
when a new channel
or
input is tuned.
•
Turning
off
the
TV
will
clear
the History List.
Note: Whenever an item is selected that cannot
be
tuned (for various reasons), the
TV
will
automatically tune
to
the previously viewed
channel
or
input.
Adding channels and inputs to the History
List:
As a channel
or
input is tuned, the Channel
Browser™
adds
it
to the History List and displays
it
on the "right
side"
of
the Channel Browser™. Previously tuned
channels/inputs are "shifted" to the left, eventually
••
.
BACK
movIng oft the left sIde. Press
~
....
to
surf
backward
through the previously tuned channels/inputs. Any
channel
or
input that is tuned repeatedly will not be
repeated
in
the History List, but instead is moved to
the end
of
the list on the right side
of
the Channel
Browser™.
The
Channel
Browser™ will store
the
following
channels:
• All channels that are tuned using the numeric buttons
on the remote control.
• All
channels
that are tuned using
rM
or
l!J
on
the
remote
control.
Adding
and
clearing
channels
and
inputs
in
the
History
List
I
32
To Next Page
Loading...
