Sound
problems
• Check the antenna/cable connections
(~
Chapter
2).
•
The
station may have broadcast difficulties. Try
another channel.
• The sound may be muted. Press
VOLUME.
•
If
you hear no sound, try setting the
MTS
feature
to
Stereo
mode
(IQ~
page 45).
•
If
you are not receiving a second audio program
from a known
SAP
source, make sure the
MTS
feature
is
set to
SAP
mode
(~page
45).
•
If
you hear audio that seems "incorrect" for the
program you are watching (such as music or a
foreign language), the
SAP
mode may be on. Set
the
MTS
feature to
Stereo
mode
(~page
45).
Remote
control
problems
• Make sure the remote control is set to the correct
device mode
(~ page 22).
• Remove ali obstructions between the remote
control and the
TV.
• The remote control batteries may be dead.
Replace the batteries
(~
page 21).
• Your TV remote control may not operate
certain features on your external device. Refer
to the owner's manual for your other device
to determine its available features.
If
your TV
remote control does not operate a specific feature
on another device, use the remote control that
came with the device
(~
pages 23-27).
•
If
the
TV
still does not act as expected, use the
Reset Factory Defaults procedure
(~page
34).
Channel
tuning
problems
• Make sure the remote control
is
set to the correct
device mode
(~
page 25).
• The channel may have been erased from the
channel memory by the
Programming
channels
automatically
feature. Add the channel to the
channel memory
(~
page 31).
• The channel may be blocked by the
LOCK
feature. Unblock the channel
(~page
48).
•
If
you are unable to tune digital channels, check
the antenna configuration
(1& page 30).
If
you
are still unable to tune digital channels, clear all
channels from the channel list and reprogram
channels into the channel memory
(1& page 31).
If
you are still unable to tune digital channels,
use the Reset Factory Defaults procedure
(~
page 34). Also see
"TV
stops responding to
controls" and "Other problems"
(1& page 62).
Closed
caption
problems
•
If
the program or video you selected
is
not
closed-captioned, no captions will display
(~
page 43).
•
If
text
is
not available, a black rectangle may
appear. If this happens, turn off the closed
caption feature
(~
page 43).
• A closed-caption signal may not display
correctly in the following situations: a) when
a videotape has been dubbed; b) when the
signal reception is weak;
or
c) when the signal
reception
is
nonstandard
(~page
43).
Rating
blocking
(V-Chip)
problems
•
If
you forget your PIN code: While the PIN
. .
d'
I d RECALL
code
entenng
screen IS
ISP
aye , press 0
four times within 5 seconds. The PIN code you
previously stored will be cleared
(IQ?
page 46).
No
REGZA-LiNK
operation
• The REGZA-LINK feature
is
available for
Toshiba REGZA-LINK compatible devices.
• Make sure the HDMI cables with the HDMI
Logo
(HOm.·)
are used.
• When the connected REGZA-LINK device
does not work correctly after you have changed
settings
of
the device, turn off your
TV
and
unplug the power cord, then plug and turn on
again.
•
If
several devices are connected, REGZA-LINK
feature may not operate properly.
• Read the instruction manual furnished with the
connected REGZA-LINK device.
HDMI
problems
For HOMI cables
• Make sure to use cables with the
HOM
I Logo
(HOm.·)
(~
page 13).
Network
problems
Cannot connect
to
network
• Check the Router with Hub and the
TV
connections (1& pages 20).
• Make sure the Router with Hub
is
connected to
the
TV's
LAN
port correctly
(~page
20).
• Make sure your network address is set up correctly.
No network connection
• The LAN cables are not connected properly or at
all. Connect all cables
(1& pages 20).
• Make sure the power cords
of
the all devices are
plugged in.
• Make sure your network address
is
set up
correctly
(~"Setting
up
the network address for
the
LAN
port").
63
I
To Next Page
Loading...
