Toshiba Q9+ - Direct Access Parameters;Numbers

To Next Page

To Previous Page

Program Menu Navigation

Q9 Plus ASD Install/Op Manual

62 https://www.toshiba.com/tic/

COMMUNICATIONS

Communication Options

Communication Option Setting 11

F842

Communication Option Setting 12

F843

Communication Option Setting 13

F844

Communication Option Setting 14

F845

Communication Option Setting 15

F846

Communication Option Setting 16

F847

Communication Option Setting 17

F848

Communication 2 Time-Out Condition

F849

Disconnection Detection Extended Time

F850

ASD Operation at Disconnection

F851

Preset Speed Operation

F852

Communication Option Station Address Monitor

F853

Communication Option Speed Switch Monitor Devi-

ceNet/CC-Link

F854

PASSWORD AND LOCK OUTS

Password and Lockouts

Enter Password

N/A

Change Password

N/A

Lock Outs

N/A

Program Mode Menu Navigation

Primary Menu Sub Menu Parameter Name

Parameter

Number

Password and

Lockout

Main Page

Electrical Hazard Symbol13
Explosion Hazard Symbol13
— The Metal Of Conduit Is Not An Acceptable Ground —15
Grounding Capacitor Switch15
Dynamic Braking Precaution18
- Figure 1. Typical Circuit Breaker Configuration.21
Power Connections22
- Figure 2. Typical Q9 Plus ASD 3- phase input/output terminals and the Grounding Capacitor Switch.22
- Power Connection Requirements23
  - Figure 3. Q9 Plus ASD/Motor Typical Connection Diagram.23
System Grounding23
- Grounding Capacitor24
Terminal Descriptions27
- Figure 8. The relay is shown in the normal operating condition (default setting). During a faulted condition the relay connection is FLC-to-FLA.29
- Figure 9. Terminal Board.29
Terminal Board I/O Configurations30
- Figure 10. Discrete Input.30
- Figure 11. RR Input.30
- Figure 12. RX Input.30
- Figure 13. V/I Input.30
- Figure 14. P24 Output.30
- Figure 15. PP Output.30
- Figure 16. OUT1/OUT2 Output.30
- Figure 17. FP Output.30
- Figure 18. AM/FM Output.30
- Figure 19. Fault Relay (shown not faulted).30
Typical ASD Connection Diagram31
- Figure 20. The Q9 Plus Typical Connection Diagram.31
Start Up and Test32
- Figure 21. The Q9 Plus ASD Electronic Interface Features.34
LED/LCD Screens35
- LED Screen Display35
- LED Character/Font Information35
- LCD Screen Display35
- LCD Character/Font Information35
Using the LCD Screen36
- Primary Menus of the LCD Screen36
- Remote Mounting Hardware37
- Remote Mounting Installation Precautions37
- Remote Mounting Using the Mounting Kit37
  - Figure 25. Front Panel Removal/Front Panel Connector Assembly.38
  - Figure 26. Remote Mounting Dimensions (inches/millimeters).38
- Remote Mounting without the Mounting Kit39
  - Figure 27. EOI Remote Mounting Dimensions (inches/millimeters).39
Search For Default Setting Changes41
Command and Frequency Control Selections46
- Figure 28. Command- and Frequency-Control Source Relationship.46
Command Control47
Frequency Control47
- Figure 29. Q9 Plus ASD Root Menu Navigation.48
Frequency Command Mode48
- Frequency Setting48
EOI Command Mode48
Monitor Mode50
Program Mode Menu Navigation52
- Figure 30. Input the electrical specifications to the motor.75
- Figure 31. Input the specifications to the transducer.75
- Figure 32. Local mode verification.76
- Figure 33. Set the maximum threshold value.76
- Figure 34. Set the minimum threshold value.76
- Figure 35. Complete the virtual linear pump setup.77
- Figure 36. Select an Operating Mode.77
- Figure 37 . UP/Down Frequency Operation Control Timing Diagram.143
Linear acceleration and deceleration is the default pattern and is used on most applications.187
- Figure 38 . Using Acc/Dec Switching.189
- Viewing Trip Information283
- Trip Record at Monitor Screen283
- Trip History284
- Clearing a Trip284
Blank Page2
Blank Page305

Toshiba Q9+ - Direct Access Parameters;Numbers

Table of Contents

Related product manuals