Trane IntelliPak CGAF Series - GBAS (0-5 VDC) Binary Output Definition

29
System Programming SETUP
1. Press the + or - key until the proper value is displayed.
Used on Units:
With GBAS 0-5VDC Module
2. Press the ENTER key to confirm this choice.
Possible Values:
Not Assigned
3. Press the NEXT key until the following screen is displayed. Indicate Selected Diag Alarms
Indicate Unit at Max Capacity
The following screens will display if "Indicate selected diagnostics Indicate any comp is running
alarms" is assigned to any of the 5 Binary Output Definitions.
1.To view the factory preset or to modified the factory presets
to meet specific application requirements, press the
ENTER key. If no adjustments are required, press the NEXT
k
ey to a
d
vance to t
h
e
f
o
ll
ow
i
ng screen.
2. Press the + or - key until the proper value is displayed. If "YES"
is assigned to "Any Active Diagnostic", pressing the NEXT key
Used on Units:
With GBAS 0-5VDC Module
will advance to the Binary Output 2 Definition screen. Assigning
Possible Values:
Yes, No
"NO" to the "Any Active Diagnostic" will advance to the selectable
diagnostic screens.
3. Press the ENTER key to confirm each choice.
4. Press the NEXT key to scroll through each Active Diagnostic.
Active Diagnostics
CGM ICS Temperature Sensor Fail Liquid Pressure Sensor Fail Ckt 1
CGM Module Data Storage Error Liquid Pressure Sensor Fail Ckt 2
CGM OA Temp Sensor Failure Low Ambient Evap Soln Pump Override
CGM Zone Temp Sensor Failure Low Soln Cutout Temp (Man)
Ckt 1 Pumpdown Terminated by Time Low Soln Cutout Temp (Auto)
Ckt 2 Pumpdown Terminated by Time Low Press Control Open - Ckt 1
Comp Contactor Fail - Ckt 1 Low Press Control Open - Ckt 2
Comp Contactor Fail - Ckt 2 LSS Adjusted To Maintain Min Diff
Compressor Trip - Ckt 1 EST/LST Low Temperature Indication
Compressor Trip - Ckt 2 MCM Communications Failure
Comp Protection LPC Open - Ckt 1 Sat Liquid Temp Sensor Fail Ckt 1
Comp Protection LPC Open - Ckt 2 Sat Liquid Temp Sensor Fail Ckt 2
Cond Temp Sensor Failure - Ckt 1 SCM Communications Failure
Cond Temp Sensor Failure - Ckt 2 Suction Pressure Sensor Fail Ckt 1
Current Sensor Module Comm Fail Suction Pressure Sensor Fail Ckt 2
Emergency Stop Suction Temp Sensor Failure - Ckt 1
Evap Entering Soln Temp Sensor Fail Suction Temp Sensor Failure - Ckt 2
Evap Leaving Soln Temp Sensor Fail Superheat/Subcool Module Comm Fail
Evap Solution Flow Proving Switch BAS Module Comm Failure
Evap Solution Flow Loss BAS/NETWORK Comm Failure
Extern Leaving Soln STP Input Fail Unit HI Communications Failure
GBAS 0-5VDC Module Comm Failure
GBAS 0-10VDC Module Comm Fail
Hot Start Load Limit (Auto)
Hot Start Load Limit (Info)
Hot Start Load Limit (Man)
Hot Start Load Limit STP Fail
IBTS Adjusted To Maintain Min Diff
Ice Build Terminate Setpoint Fail
Leaving Solution Setpoint Fail
GBAS (0-5VDC) Binary Output 1 Definition
OUTPUT IS NOT ASSIGNED
GBAS (0-5VDC) Output 1 Alarm Assignments
Press ENTER to Review or Ad
j
ust
Assign Diag To GBAS (0-5V) Output #1 ?
Any Active Diagnostic (No)