How to fix poor print quality on TSC Barcode Reader?
To fix poor print quality on your TSC Barcode Reader, start by reloading the media correctly. Clean the print head to remove any dust or adhesive. Adjust the print density and print speed settings. Run a self-test to check the print head pattern for missing dots, which would indicate a damaged print head element.
Why is my TSC Barcode Reader skipping labels when printing?
If your TSC Barcode Reader is skipping labels during printing, ensure the label size is correctly specified in your settings. Calibrate the sensor using the Auto Gap or Manual Gap options. Also, clear any dust from the GAP/Black mark sensor using a blower.
What does it mean when TSC Barcode Reader status from DiagTool shows “Out of Paper”?
If the TSC Barcode Reader status from DiagTool shows “Out of Paper”, supply a new label roll. Ensure the label roll is installed correctly. Calibrate the gap/black mark sensor.
Why is my TSC Barcode Reader printing irregularly?
If your TSC Barcode Reader is exhibiting irregular printing, try turning it off and on to exit the dump mode. Also, re-set the Rs-232 setting.
What to do if my TSC Barcode Reader displays a memory full error?
To resolve a 'Memory full' error on your TSC Barcode Reader, delete any unused files in the FLASH/DRAM.
What to do if my TSC Barcode Reader is not printing?
If your TSC Barcode Reader is not printing, first, reconnect the interface cable or try a new one to ensure a secure connection. If using a serial port, verify that the cable is pin-to-pin connected; if not, replace it. Also, check that the serial port settings on both the host and the printer are consistent, with the default baud rate set to 9600, n, 8, 1. In the Windows driver, confirm that the correct printer port is selected. For Ethernet connections, ensure the Ethernet RJ-45 connector's green LED is lit and the amber LED is blinking. Check if the printer obtains an IP address in DHCP mode or if the static IP address is correctly configured. Allow a few seconds for the printer to establish communication with the server before rechecking the IP address settings.
Why is my TSC Barcode Reader continuously feeding labels?
To resolve continuous feeding labels with your TSC Barcode Reader, start by initializing the printer and calibrating the gap/black mark sensor. Ensure the label size is accurately set in your labeling software or program to match the installed paper. Also, check for and remove any labels stuck inside the printer mechanism near the sensor area.
Why doesn't the power indicator illuminate on my TSC Barcode Reader?
If the power indicator on your TSC Barcode Reader doesn't illuminate, ensure the power cord is properly connected to both the printer and the outlet. Also, make sure that the printer is switched on.
What to do if my TSC Barcode Reader has no response?
If your TSC Barcode Reader is not responding, ensure the power switch is turned on. Check if the green LED on the power supply is lit; if not, the power supply may be broken. Verify that both power connections—from the power cord to the power supply and from the power supply to the printer—are securely connected.
What to do if TSC Barcode Reader status from DiagTool shows “Head Open”?
If the TSC Barcode Reader status from DiagTool shows “Head Open”, close the print carriage.
General| Resolution | 203 dpi / 300 dpi |
|---|---|
| Print Speed | Up to 6 ips (inches per second) |
| Processor | 32-bit RISC |
| Interface | USB 2.0 |
| Scanning Technology | Thermal transfer / Direct thermal |
| Scanning Speed | Up to 6 ips (inches per second) |
| Scanning Resolution | 203 dpi / 300 dpi |
| Scanning Distance | N/A (Not applicable for barcode printers) |
| Additional Interface | Bluetooth (optional) |
| Power Supply | AC 100-240V, 50/60Hz |
| Operating Temperature | 5 ~ 40°C (41 ~ 104°F) |
| Storage Temperature | -40 ~ 60°C (-40 ~ 140°F) |
| Humidity | 20% to 85% (non-condensing) |
| Supported Barcode Types | Code 39, Code 128, UPC-A, UPC-E, EAN-8, EAN-13, PDF-417, DataMatrix, QR code |
Overview of the printer's key features and capabilities.
Detailed technical specifications for the DA210/DA220 series printers.
Instructions for unpacking and inspecting the printer upon receipt.
Identification of components on the front of the printer.
Identification of internal components of the printer.
Identification of the ports and controls on the rear of the printer.
Step-by-step guide for initial printer setup and connection.
Instructions on how to load standard media rolls into the printer.
Instructions for loading external media rolls using the printer's features.
Guide for loading media specifically for peel-off operation.
Instructions for loading media when using the cutter function.
Steps to load linerless media for tear-off dispensing.
How to load linerless media for cutter dispensing.
Guide to installing the optional adapter for 1.5-inch paper cores.
Explanation of LED colors and their meanings for printer status.
Description of the functions of the printer's main button.
How to access and use power-on utilities for calibration and settings.
Steps to launch and begin using the TSC Console management software.
Configuration steps for connecting the printer via Ethernet using TSC Console.
Using TPH Care to check and manage printhead condition and dot failures.
Overview of various printer functions available within the TSC Console.
How to configure actions performed after printing, like cutting or peeling.
Common LED status indicators and their corresponding troubleshooting procedures.
Identifying and resolving common printing issues like no print or poor quality.
Guidelines for cleaning and disinfecting the printer for optimal performance.
Essential safety and handling precautions during maintenance tasks.
List of recommended cleaning supplies for printer maintenance.
Detailed procedures for cleaning various printer components.
Information on compliance with various regulatory standards like CE, FCC, and IC.
To Next Page
