Why is my TSC Label Maker continuously feeding labels?
If your TSC Label Maker is continuously feeding labels, the printer settings may be incorrect. To resolve this, perform the initialization and gap/black mark calibration.
Why is my TSC Label Maker producing poor print quality?
If your TSC Label Maker is producing poor print quality, ensure that the top cover is completely closed and that both the right and left side levers are properly latched. Check that the correct 24V DC power supply is connected to the printer. Reload the supply and verify it's loaded correctly. Finally, inspect the print head for any accumulated dust or adhesives and clean it if necessary.
How to troubleshoot a paper jam in my TSC Label Maker?
If the TSC Label Maker is experiencing a paper jam, there are several potential causes. First, the gap/black mark sensor sensitivity might not be set properly; try calibrating the sensor. Second, ensure that the label size is correctly set in your labeling software or program to match the installed paper. Lastly, check for any labels stuck inside the printer mechanism near the sensor area and remove them.
What to do if my TSC Label Maker shows an error?
If your TSC Label Maker displays an 'Error' message, it could be due to a few reasons. First, check if you are out of labels or ribbon. If so, load a new roll of labels or ribbon, following the loading instructions, and then press the FEED button to resume printing. If the error persists, the printer settings might be incorrect. In this case, initialize the printer using the 'Power on Utility' or 'Diagnostic Tool'.
How to fix a TSC Label Maker that shows no response?
If your TSC Label Maker is showing 'No response', start by turning on the power switch. Check if the green LED is lit on the power supply; if it's not, the power supply is likely broken. Also, ensure that both power connections—from the power cord to the power supply and from the power supply to the printer power jack—are securely connected.
General| Print technology | Direct thermal |
|---|---|
| Vertical printing | Yes |
| Maximum resolution | 203 x 203 DPI |
| Maximum print height | 2286 mm |
| Maximum printing width | 54 mm |
| Ethernet LAN | No |
| USB 2.0 ports quantity | 1 |
| Connectivity technology | Wired |
| Flash memory | 4 MB |
| Certification | FCC, CE, TUV, CUL, UL, CCC, C-Tick |
| Internal memory | 8 MB |
| Built-in barcodes | 1D, 2D, CODABAR (NW-7), Code 128 (A/B/C), Code 39, Code 93, EAN128, EAN13, EAN8, Interleaved 2/5, MaxiCode, PDF417, POSTNET, QR Code, UPC-A, UPC-E |
| Built-in processor | RISC 32-bit |
| Compatible memory cards | SD |
| Power requirements | 100 - 240 |
| AC adapter output current | 2 A |
| AC adapter output voltage | 24 V |
| Display | LCD |
| Product color | - |
| Core diameter | 38 mm |
| Ribbon length | 90 m |
| Media thickness | 0.06 - 0.19 mm |
| Maximum label width | 60 mm |
| Maximum label length | 2.286 m |
| Maximum roll diameter | 127 mm |
| Supported paper width | 15 - 60 mm |
| Maximum media length (imperial) | 90 \ |
| Supported paper width (imperial) | 0.59 - 2.36 \ |
| LED indicators | Power, Status |
| Storage temperature (T-T) | -40 - 60 °C |
| Operating temperature (T-T) | 41 - 104 °F |
Weight and Dimensions| Depth | 209 mm |
|---|---|
| Width | 109 mm |
| Height | 171 mm |
Overview of the TDP-225/TDP-225W bar code printer's features and performance.
Lists regulatory compliances for the printer, including CE, FCC, UL, CUL, and C-Tick.
Instructions for inspecting the printer and its included accessories after unpacking.
Detailed views of the TDP-225 and TDP-225W printer models, showing front, interior, and rear components.
Steps for physically setting up the printer, including placement and power connection.
Comprehensive guide on loading various types of media, including roll labels, external, peel-off, and cutter modes.
Explains how to use the Diagnostic Utility for printer configuration, firmware updates, and troubleshooting.
Step-by-step instructions for configuring the printer's Ethernet interface via USB or direct Ethernet connection.
Guide on installing a MicroSD card and details on recommended specifications and file system.
Provides instructions and dimensions for securely mounting the printer on a wall.
Describes the meaning of different LED colors and blinking patterns for printer status indication.
Details the basic functions of the printer's button, such as feeding labels and pausing print jobs.
Explains how to access and utilize power-on utilities for sensor calibration, initialization, and self-tests.
Guides users through common LED status issues, their possible causes, and recovery procedures.
Addresses common printing issues like 'Not Printing', 'No print on the label', 'Paper Jam', and 'Poor Print Quality'.
Explains LCD error messages for the TDP-225 model, including causes and solutions.
Provides detailed methods and intervals for cleaning printer parts like the print head, platen roller, and sensors.
To Next Page
