EasyManua.ls Logo

TSC TTP-343 Plus - User Manual

TSC TTP-343 Plus
50 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
USER’S
MANUAL
TTP-245 Plus / TTP-343 Plus
TTP-247 / TTP-345
THERMAL TRANSFER / DIRECT THERMAL
BAR CODE PRINTER

Table of Contents

Other manuals for TSC TTP-343 Plus

Preview: Service Manual
Service Manual72 pages
Preview: Programming Manual
Programming Manual252 pages

Questions and Answers

  • W
    William SnyderSep 9, 2025
    Why is my TSC Barcode Reader not printing?
    • C
      Christopher RobinsonSep 9, 2025
      Several factors can cause a TSC Barcode Reader not to print. Here's what to check: * Ensure the interface cable is securely connected. * If using a serial port, verify the cable is pin-to-pin connected, replace if needed. * Confirm the serial port settings match between the host and the printer; reset if necessary. * In the Windows driver, select the correct printer port. * Verify that the Ethernet IP, subnet mask, and gateway are properly configured.
  • L
    Levi ShawSep 12, 2025
    What to do if TSC Barcode Reader has no response?
    • M
      Martin HensonSep 12, 2025
      If your TSC Barcode Reader is not responding, check these items: * Make sure the power switch is turned on. * Verify the green LED is lit on the power supply. If not, the power supply may be broken. * Ensure both power connections, from the power cord to the power supply and from the power supply to the printer, are securely connected.
  • A
    Ann BrownSep 13, 2025
    How to fix a paper jam in my TSC Barcode Reader?
    • C
      Christopher WillisSep 13, 2025
      To resolve a paper jam in your TSC Barcode Reader: * Calibrate the gap/black mark sensor. * Ensure the label size is correctly set in your labeling software or program to match the installed paper. * Check the printer mechanism near the sensor area for stuck labels and remove them.
  • H
    Heather HayesSep 15, 2025
    Why is my TSC Barcode Reader continuously feeding labels?
    • D
      Dalton HernandezSep 15, 2025
      If your TSC Barcode Reader is continuously feeding labels, the printer settings may be incorrect. Perform initialization and gap/black mark calibration to resolve this issue.
  • T
    Theresa Bolton MDSep 18, 2025
    How to resume printing on a paused TSC Barcode Reader?
    • M
      Mark BrightSep 18, 2025
      If your TSC Barcode Reader is paused, simply press the FEED button to resume printing.

Summary

Introduction and Getting Started

Initial Setup Overview

Steps for unpacking, inspection, and basic setup of the printer.

Printer Setup Procedures

Printer Setup and Connection

Step-by-step guide for connecting and configuring the printer.

Loading Ribbon and Labels

Instructions for properly installing printer ribbon and label stock.

Optional Module Installation

Procedures for installing peel-off and cutter modules.

Memory Card Installation

Guide for installing an SD memory card into the printer.

Diagnostic and Network Setup

Using the Diagnostic Tool

Guide on launching and utilizing the printer's diagnostic utility software.

Ethernet Configuration

Steps for setting up network connectivity via USB, RS-232, or Ethernet.

Power-on Utilities

Sensor Calibration and Tests

Procedures for sensor calibration, self-tests, and dump mode entry.

Printer Initialization and Control

Steps for printer initialization, sensor mode configuration, and AUTO.BAS control.

Maintenance and Troubleshooting

Printer Cleaning and Maintenance

Methods and materials for cleaning and maintaining the printer.

Troubleshooting Printer Issues

Guide to resolving common printer problems using LED status and print quality checks.

LED and Button Operations

Explanations of printer status indicators and control buttons.

TSC TTP-343 Plus Specifications

General IconGeneral
Print MethodThermal Transfer / Direct Thermal
Processor32-bit RISC CPU
Power SupplyAC 100-240V, 50/60Hz
Max Print Width108 mm (4.25")
Max Print Speed102 mm (4ips)
Memory8 MB Flash, 8 MB SDRAM
InterfaceUSB 2.0, Serial
Media TypeContinuous
Media Width25.4 mm to 112 mm
Weight2.5 kg
Supported Barcode TypesCode 39, Code 128, QR Code
Supported OSWindows

Related product manuals