What does ‘Low Heat’ mean on my Tuttnauer 2340EKA?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer 2340EKA?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What to do if Tuttnauer 2340EKA Laboratory Equipment process fails during heating stage with a HIGH TEMP message?
If your Tuttnauer Laboratory Equipment process fails while initiating the heating stage and displays a HIGH TEMP message, try changing the setting of the thermostat.
How to troubleshoot Tuttnauer 2340EKA machine not responding?
If your Tuttnauer Laboratory Equipment machine isn't responding, verify that the main switch is in the ‘On’ position, the power cord is properly connected to both the machine and the mains, and the circuit breaker hasn't tripped. Also, check the reset button on the cut-out thermostat.
What should I do if my Tuttnauer Laboratory Equipment shows ‘Low Pres’?
If the 'Low Pres' message is displayed on your Tuttnauer Laboratory Equipment, clean the water level electrode inside the vessel. Also, ensure the door is fully closed, the door gasket is properly seated, and there is no steam leakage. Check the leveling of the machine.
How to fix ‘High Pres’ error on Tuttnauer Laboratory Equipment?
If the 'High Pres' message appears on your Tuttnauer Laboratory Equipment, the air jet might be clogged; clean it. It could also mean that the heating elements are continuously on, or the temperature sensor is faulty. In these cases, contact a technician.
How to unclog the drain on Tuttnauer Laboratory Equipment?
If the drain of your Tuttnauer Laboratory Equipment is clogged: 1. Open the drain by turning it counterclockwise and place a heavy object over the reservoir cover. 2. Blow compressed air into the drain to force debris back into the reservoir, then clean out the reservoir. 3. Alternatively, disassemble the drain valve, clean it, and blow out the line. Reassemble the valve, ensuring the large 'O' ring is properly seated.
What should I do if my Tuttnauer Laboratory Equipment displays ‘High Pres’?
If your Tuttnauer Laboratory Equipment displays ‘High Pres’, clean the air jet. Ensure the sterilization time and temperature are set correctly; if unsure, use the default settings. Also, make sure the autoclave is not too heavily loaded.
What to do if my Tuttnauer 2340EKA is not responding?
If your Tuttnauer Laboratory Equipment is not responding, ensure the main switch is in the ‘On’ position. Also, verify the power cord is properly connected to both the machine and the mains. Check the reset button on the cut-out thermostat and make sure the circuit breaker hasn't tripped; lift the circuit breaker lever if it has.
Why is my Tuttnauer 2340EKA leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, ensure the door is tightened enough and the door gasket is sealing the chamber. If necessary, replace the door gasket.
Lists electrical data, including voltage, amperage, and fuse ratings.
Lists detailed chamber dimensions, volumes, and pressure ratings.
Describes the operation and functions of the control panel keys.
Lists error messages, their causes, and associated safety measures.
Details sterilization parameters and sequence for unwrapped items.
Covers electrical connection, safety, and initial unit configuration.
Outlines daily, weekly, and periodic maintenance tasks.
Covers machine response, heat, water level, and pressure issues.
Addresses issues with exhaust time, door seals, clogged strainers, and drain problems.
Solutions for failing spore tests, wet/burned wraps, instrument rusting, and drying problems.
General| Brand | Tuttnauer |
|---|---|
| Model | 2340EKA |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
