What does ‘Low Heat’ mean on my Tuttnauer 2540EKA Laboratory Equipment?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer Laboratory Equipment?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What to do if Tuttnauer 2540EKA process fails during heating stage with a HIGH TEMP message?
If your Tuttnauer Laboratory Equipment process fails while initiating the heating stage and displays a HIGH TEMP message, try changing the setting of the thermostat.
How to troubleshoot Tuttnauer 2540EKA Laboratory Equipment machine not responding?
If your Tuttnauer Laboratory Equipment machine isn't responding, verify that the main switch is in the ‘On’ position, the power cord is properly connected to both the machine and the mains, and the circuit breaker hasn't tripped. Also, check the reset button on the cut-out thermostat.
What should I do if my Tuttnauer 2540EKA Laboratory Equipment shows ‘Low Pres’?
If the 'Low Pres' message is displayed on your Tuttnauer Laboratory Equipment, clean the water level electrode inside the vessel. Also, ensure the door is fully closed, the door gasket is properly seated, and there is no steam leakage. Check the leveling of the machine.
How to fix ‘High Pres’ error on Tuttnauer 2540EKA Laboratory Equipment?
If the 'High Pres' message appears on your Tuttnauer Laboratory Equipment, the air jet might be clogged; clean it. It could also mean that the heating elements are continuously on, or the temperature sensor is faulty. In these cases, contact a technician.
How to unclog the drain on Tuttnauer Laboratory Equipment?
If the drain of your Tuttnauer Laboratory Equipment is clogged: 1. Open the drain by turning it counterclockwise and place a heavy object over the reservoir cover. 2. Blow compressed air into the drain to force debris back into the reservoir, then clean out the reservoir. 3. Alternatively, disassemble the drain valve, clean it, and blow out the line. Reassemble the valve, ensuring the large 'O' ring is properly seated.
What should I do if my Tuttnauer 2540EKA Laboratory Equipment displays ‘High Pres’?
If your Tuttnauer Laboratory Equipment displays ‘High Pres’, clean the air jet. Ensure the sterilization time and temperature are set correctly; if unsure, use the default settings. Also, make sure the autoclave is not too heavily loaded.
What to do if my Tuttnauer 2540EKA is not responding?
If your Tuttnauer Laboratory Equipment is not responding, ensure the main switch is in the ‘On’ position. Also, verify the power cord is properly connected to both the machine and the mains. Check the reset button on the cut-out thermostat and make sure the circuit breaker hasn't tripped; lift the circuit breaker lever if it has.
Why is my Tuttnauer Laboratory Equipment leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, ensure the door is tightened enough and the door gasket is sealing the chamber. If necessary, replace the door gasket.
Specifies acceptable physical and chemical characteristics for water.
Step-by-step guide for replacing the HEPA air filter.
Procedure for emptying and cleaning the water reservoir.
Instructions for cleaning the air jet to ensure proper operation.
How to remove and install a new door gasket.
Procedure for monthly checking of the safety valve.
Guide to replacing blown fuses for water and air pumps.
Steps for cleaning the water outlet strainer.
Procedure for using Chamber Brite for cleaning and descaling.
Instructions for cleaning the water sensor for accurate level reporting.
Solutions for when the autoclave fails to power on or operate.
Troubleshooting steps for the 'Low Heat' display.
Solutions for the 'Low Water' indicator.
Troubleshooting steps for the 'Low Pres' display.
Solutions for the 'Low Temp' indicator and potential causes.
Troubleshooting for 'High Temp' messages and sensor issues.
Solutions for the 'High Pres' display and potential causes.
Steps to resolve a clogged drain valve or line, and chamber fill issues.
General| Brand | Tuttnauer |
|---|---|
| Model | 2540EKA |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
