What does 'Air Error' mean on Tuttnauer 3850 ELVG-D Laboratory Equipment?
If your Tuttnauer Laboratory Equipment displays 'Air Error' at the end of the cycle, it means the autoclave did not reach atmospheric pressure after 10 minutes. Wait until the autoclave reaches atmospheric pressure and then perform a new cycle.
How to fix Tuttnauer 3850 ELVG-D printer that doesn't print anything on the paper?
If your Tuttnauer Laboratory Equipment printer prints, but nothing appears on the paper, it likely means the paper roll isn't installed correctly. Ensure you install the paper roll the right way, noting that only one side of the paper is printable.
What does 'High Pressure (Ending)' mean on my Tuttnauer Laboratory Equipment?
If your Tuttnauer Laboratory Equipment displays 'High Pressure (Ending)', it means the system couldn't reach atmospheric pressure ± 10kPa during the ending stage. Perform a new cycle.
How to fix slow exhaust phases on Tuttnauer Laboratory Equipment?
If the fast or slow exhaust phases aren't functioning correctly, leading to high chamber pressure or a prolonged exhaust time, consider these potential causes: * The fast or slow exhaust valves might be stuck or damaged. Repair or replace any damaged valves. * The steam valve could be leaking. Repair or replace the steam valve. * There might be a control system issue. Replace the control boards.
Why is my Tuttnauer 3850 ELVG-D Laboratory Equipment leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, it could be due to: 1. A dirty door gasket. Clean the door gasket. 2. A damaged door gasket. Call for service.
Why are my Tuttnauer Laboratory Equipment sterilization results unsatisfactory?
If you're experiencing unsatisfactory sterilization results, consider the following possible causes: * There might be incomplete removal of air pockets. * Sterilization conditions might involve improper temperature or pressure being too low, or the sterilization time being too short. Set the correct temperature and time according to the type and quantity of material. * Incorrect loading of the autoclave may be trapping air in the load.
Why is the air detector failing in my Tuttnauer Laboratory Equipment?
If the air detector fails, consider the following possible causes: * The steam quality might not be proper. Check the steam quality and non-condensable gases. * The induced air valve might be open or leaking. Close or repair the induced air valve.
What does 'Low Pressure' mean on my Tuttnauer 3850 ELVG-D Laboratory Equipment?
If your Tuttnauer Laboratory Equipment displays 'Low Pressure', it means the chamber pressure dropped below the sterilization pressure (134°C = 304 kPa, 121°C = 205 kPa) for 2 seconds during the sterilization stage. Try performing a new cycle.
What does 'High Temp' mean on my Tuttnauer 3850 ELVG-D?
If the 'High Temp' message is displayed on your Tuttnauer Laboratory Equipment, it means the temperature rose 7°F (4°C) above the sterilization temperature during the sterilization stage for 2 seconds during the sterilization cycle. Perform a new cycle.
What does 'Low Temp' mean on my Tuttnauer 3850 ELVG-D Laboratory Equipment?
If your Tuttnauer Laboratory Equipment displays 'Low Temp', it indicates that the temperature dropped below the sterilization temperature for more than 1 second during the sterilization cycle. Try performing a new cycle.
Information on display screens, operational messages, and error displays.
Displays for aborted, canceled, or failed sterilization cycles.
Changing operational parameters, system settings, and maintenance procedures.
How to select programs, start cycles, and handle errors.
Safe procedures for unloading the autoclave and moving the device.
Preventive maintenance for daily, weekly, and periodic checks.
Solutions for machine not responding, printer malfunctions, and door leaks.
Troubleshooting for vacuum, temperature, pressure, supply, and sensor errors.
General| Type | Autoclave |
|---|---|
| Chamber Volume | 85 L |
| Power Supply | 220-240V, 50/60Hz |
| Chamber Material | Stainless Steel |
| Temperature Range | 105°C - 137°C |
| Safety Features | Safety valve, Door protection interlock, Overheat protection |
To Next Page
