What to do if Tuttnauer Laboratory Equipment displays ‘Low Water’?
If your Tuttnauer Laboratory Equipment displays a ‘Low Water’ message, you should: 1. Verify that there is water in the reservoir, and add water if needed. 2. Clean the water level electrode inside the vessel. 3. Check the leveling of the machine.
What to do if Tuttnauer 5075 EL Laboratory Equipment displays ‘Low Pres’?
If the Tuttnauer Laboratory Equipment displays ‘Low Pres’, verify that no instruments are in contact with the water level electrodes. Also, check the door for leakage and replace the door gasket if necessary.
What to do if Tuttnauer 5075 EL Laboratory Equipment displays ‘High Pres’?
If the Tuttnauer Laboratory Equipment displays ‘High Pres’, clean the water level electrode inside the vessel. Also, check the levelling of the machine.
What to do if Tuttnauer 5075 EL Laboratory Equipment is not responding?
If the Tuttnauer Laboratory Equipment is not responding, you should: 1. Check the outlet and verify that the voltage requirements have been met, including phase. 2. Ensure the main switch is in the ‘On’ position. 3. Confirm the power cord is properly connected to both the machine and the mains.
Why is Tuttnauer 5075 EL Laboratory Equipment leaking at the door?
If the Tuttnauer Laboratory Equipment is leaking at the door, make sure the door is tightened enough. If the leaking continues, replace the door gasket.
What to do if Tuttnauer 5075 EL Laboratory Equipment displays ‘High Temp’?
If the Tuttnauer Laboratory Equipment displays ‘High Temp’, clean the water level electrode inside the vessel and check the leveling of the machine.
What to do if Tuttnauer 5075 EL Laboratory Equipment displays ‘Low Heat’?
If the Tuttnauer Laboratory Equipment displays ‘Low Heat’, make sure the machine has the proper amount of sterilization load and is not overloaded.
How to fix Tuttnauer 5075 EL when the printer prints but nothing is on the paper?
If the printer prints, but nothing appears on the paper, ensure the paper is mounted correctly, as only one side is printable. Also, make sure the paper is inserted in the printer. If the issue persists, switch off the machine and switch it back on while pressing the feed button on the printer. If a test printout appears, the printer is working, and there may be an electronics issue.
Why Tuttnauer Laboratory Equipment water does not exit chamber?
If water does not exit the chamber of your Tuttnauer Laboratory Equipment due to a clogged outlet strainer, clean the strainer according to the instructions.
What to do if Tuttnauer 5075 EL printer does not print?
If the printer does not print, switch off the Tuttnauer Laboratory Equipment and switch it back on while pressing the feed button on the printer. If the printer still does not print the test printout, there is a problem with the printer.
Provides essential safety instructions, user training, procedures, and handling of hazardous materials, starting from page 8.
Details on Program 1 for sterilizing unwrapped instruments at 134°C with fast exhaust.
Details on Program 2 for instruments at 121°C with fast exhaust and drying.
Details on Program 3 for waste materials at 121°C with slow exhaust and drying.
Details on Program 4 for liquids at 121°C with slow exhaust, no drying.
Details on Program 5 for liquids at 105°C with slow exhaust, no drying.
Details on Program 6 for materials with cooling at 121°C, no drying.
Functions of the Start/Stop key: starting, stopping, and canceling fail messages.
Messages for Low Temp, Low Heat, and High Temp conditions during operation.
Messages for Low Pres. and High Pres. conditions during operation.
Guidelines for packaging, cleaning instruments, and loading materials correctly into the chamber.
Step-by-step guide for operating the autoclave, including filling, selecting programs, loading, and starting cycles.
General safety precautions and protective equipment required for loading and unloading the autoclave.
Importance of correct loading for efficient air removal, steam penetration, and preventing damage.
Procedures for safely unloading sterilized items, visual inspection, and rejection criteria.
Overview of periodic maintenance to keep the device in good condition and reduce breakdown time.
Step-by-step guide for draining the water reservoir, including safety precautions.
Procedure for cleaning the water strainer, including safety cautions.
Procedure for checking the safety valve for blockage on different models.
Instructions for replacing the door gasket on specific autoclave models.
Troubleshooting steps when the autoclave machine is not responding to commands.
General| Model | 5075EL |
|---|---|
| Chamber Volume | 75 liters |
| Chamber Material | Stainless Steel |
| Sterilization Temperature Range | 105°C - 138°C |
| Power Supply | 50/60Hz |
| Standard Accessories | Tray |
To Next Page