Tyco T1200 User Manual

EQUIPMENT: T1200
PUBLICATION: 19A-4-O
ISSUE No. & DATE: 3 06/09
© 2006 Tyco Safety Products PAGE 1 of 13
Registered Company: Thorn Security Ltd. Registered Office: Dunhams Lane Letchworth Garden City Hertfordshire SG6 1BE
TYCO T1200 Fire Alarm Control Panel & Repeater
User Operation Manual
List of Contents
1. INTRODUCTION.....................................................2
2. T1200 USER OPERATION - FIRE AND FAULT
CONDITIONS.........................................................2
2.1 IF A FIRE IS DETECTED: .....................................2
2.2 TO SILENCE THE FIRE ALARM SOUNDERS: ........3
2.3 TO RESOUND THE FIRE ALARM SOUNDERS
AFTER THEY HAVE BEEN SILENCED
:..................3
2.4 TO RESET THE PANEL FROM A FIRE ALARM: ....3
2.5 TO OPERATE THE FIRE ALARM SOUNDERS IN
MANUAL FIRE ALARM/MUSTER MODE:...........3
2.6 IF A FAULT IS DETECTED:..................................4
2.7 TO SILENCE THE BUZZER: ................................4
2.8 SYSTEM FAULT INDICATION:............................4
3. T1200 USER INDICATIONS ..................................5
3.1 USER INDICATIONS...........................................5
3.2 USER CONTROLS ..............................................6
4. T1200 USER CONTROLS – DISABLEMENT
AND TEST CONDITIONS.....................................7
4.1 TO DISABLE/ENABLE ANY ZONE OR ZONES. ....7
4.2 TO DISABLE/ENABLE ALL SOUNDERS. .............7
4.3 TO DISABLE/ENABLE THE FIRE OUTPUT. .........7
4.4 TO DISABLE/ENABLE THE FAULT OUTPUT.......8
4.5 TO DISABLE/ENABLE FIRE PROTECTION
OUTPUT[S]. ......................................................8
4.6 TO SELECT/CLEAR ONE MAN ZONE TEST........9
4.7 TO SELECT/CLEAR ONE MAN SOUNDER TEST.9
4.8 TO ENABLE/DISABLE DELAY MODE ..............10
4.9 TO OVERRIDE THE DELAY MODE .................. 10
4.10 SILENCING THE ALARMS DURING THE DELAY
PERIOD: ......................................................... 10
4.11 RESOUNDING THE ALARMS AFTER 2 MINUTES:
[ALARMS PREVIOUSLY SILENCED] ................. 10
4.12 TO ADJUST THE BRIGHTNESS OF THE LEDS ON
THE DISPLAY
.................................................. 10
5. T1200 REPEATER PANEL USER OPERATION -
FIRE AND FAULT CONDITIONS....................10
5.1 IF A FIRE IS DETECTED:................................... 10
5.2 TO SILENCE THE FIRE ALARM SOUNDERS:...... 11
5.3 TO RESOUND THE FIRE ALARM SOUNDERS
AFTER THEY HAVE BEEN SILENCED
: ............... 11
5.4 TO RESET THE PANEL & REPEATER(S) FROM A
FIRE ALARM: ................................................. 11
5.5 TO OPERATE THE FIRE ALARM SOUNDERS IN
MANUAL FIRE ALARM /MUSTER MODE: ....... 11
5.6 IF A FAULT IS DETECTED: ............................... 11
5.7 TO SILENCE THE BUZZER:.............................. 11
5.8 SYSTEM FAULT INDICATION: ......................... 11
5.9 T1200 REPEATER PANEL OPERATION [16 ZONE
VERSION SHOWN
]........................................... 12
6. ROUTINE TESTING AND MAINTENANCE....13
7. USER RESPONSIBILITIES.................................13
8. T1200 ISOLATE/DE-ISOLATE/TEST MODE
SELECT FLOWCHART.....................................13
DANGER
THIS EQUIPMENT CONTAINS HAZARDOUS VOLTAGES
THAT CAN CAUSE DEATH, SERIOUS PERSONAL
INJURY, OR EQUIPMENT DAMAGE.
THIS EQUIPMENT CONTAINS NO USER SERVICEABLE
PARTS. ENSURE PANEL DOOR IS KEPT CLOSED.
REFER ALL MAINTENANCE TO SUITABLY QUALIFIED
PERSONNEL.

Tyco T1200 Specifications

General

Model	T1200
Operating Temperature	32°F to 120°F (0°C to 49°C)
Type	Control Panel
Input Voltage	120 VAC
Dimensions	12.5 x 10.5 x 3.5 inches

Summary

Introduction

T1200 Panel Operation: Fire and Fault Conditions

Fire Detection and Response

Describes how the panel responds to fire detection, including sounder operation, silence, and reset procedures.

Fault and System Fault Handling

Explains how to identify and handle system faults, including buzzer silencing and system failure indications.

User Interface: Indications and Controls

Indicator Descriptions

Details the various LEDs on the panel, their colors, and the operating conditions they represent.

User Control Buttons

Outlines the functionality and button availability for user controls on the panel.

Panel Controls: Disablement and Test Modes

Zone and Output Disablement

Guides on disabling and enabling specific zones, fire outputs, fault outputs, and fire protection outputs.

Sounder Control and Testing

Instructions for disabling/enabling all sounders and performing one-man sounder tests.

Delay Mode Management

Details on enabling/disabling delay modes, overriding delays, and silencing alarms during delay periods.

T1200 Repeater Panel Operation

Repeater Fire and Fault Conditions

Explains how the repeater panel indicates and responds to fire and fault conditions.

Repeater Controls and Indicators

Covers silencing, resounding, resetting, and manual alarm/muster operations on the repeater panel.

Repeater System Faults

Details system fault indications and user actions for the repeater panel.

Routine Testing and Maintenance

User Responsibilities

Isolate/De-Isolate/Test Mode Flowchart