Need help?Do you have a question about the Tyco AutoPulse Z-20 and is the answer not in the manual?
General| Brand | Tyco |
|---|---|
| Model | AutoPulse Z-20 |
| Category | Control Panel |
| Language | English |
Describes the main user interface elements and input/output methods for operating the panel.
Details the function of each component of the AUTOPULSE Z-20 User Interface, including LEDs, touchscreen, and buttons.
Explains what an alarm condition is and how the panel indicates its presence through interface messages and LEDs.
Details the sequence of events and user interface displays upon recognizing a Fire or PRI2 alarm condition.
Outlines the three primary actions for processing alarms: Acknowledge, Silence, and Reset.
Explains the two modes for acknowledging alarms: Global and Individual.
Describes the procedure to silence audible notification appliances during an alarm condition.
Details the process for resetting the system to a normal state after an alarm is resolved.
Explains how to access detailed information about specific points or zones that have triggered an alarm.
Defines Supervisory and Trouble conditions and how the panel indicates them.
Describes the panel's response and interface display for Supervisory and Trouble events.
Details the acknowledgment process for Supervisory and Trouble events, including global and individual modes.
Explains how to view detailed information for specific Supervisory or Trouble conditions.
Explains how to access the functions available on the Main Menu screen.
Lists and describes the functions accessible from the Main Menu, along with their corresponding page numbers.
Explains how to log in to the panel with different access levels.
Lists the default passcodes for the four user access levels.
Explains how to use the System Info function to get panel and component details.
Provides information on viewing the revisions of installed cards or modules.
Details how to check the latest master revisions loaded onto the panel.
Explains how to view the panel's serial number.
Shows the revisions for Bootloader, Kernel, Filesystem, and PanelUI.
Displays the IP address and MAC address of the AUTOPULSE Z-20 panel.
Explains how to modify the configuration of basic panel components.
Accesses functions to roll back to previous panel firmware versions.
Describes how to update the panel's displayed date and time.
Details how to adjust the sensitivity and precision of the touchscreen interface.
Provides access to functions for managing data on a USB key, including backup and upgrade.
Explains that the Alarm Log screen lists all received alarms.
Describes how to clear all entries from the Alarm Logs screen after investigation.
Explains that the Trouble Log screen lists all received troubles.
Describes how to clear all entries from the Trouble Logs screen after investigation.
Explains how to search for configured points under panel control.
Details the process for searching for a specific point by type and number.
Explains how to use the Diagnostics function to run tests on the panel and devices.
Describes how to re-initialize certain hardware components to reset troubles.
Details the Warm Start and Cold Start options for restarting the panel.
Explains how to access WalkTest settings for maintenance testing.
Describes how to control the piezos on the panel and remote annunciator.
Details functions for downloading configuration jobs to remote panels.
Explains how to test for earth faults in the circuit and view results.
Explains how to latch intermittent earth fault troubles to consistently display a trouble.
Describes performing a wiring test on the Notifications Appliance Circuits (NAC).
Explains how to enable or disable detection of duplicate devices on IDNet channels.
Explains how to enable or disable detection of weak answering devices on IDNet channels.
Minimizes troubles during installation or service by placing items in Install Mode.
Explains how to generate various reports on system points.
Generates a report of all alarms received by the panel.
Generates a report of all troubles received by the panel.
Generates a report on the status of TrueAlarm devices connected to the panel.
Reports on TrueAlarm Service devices including device number, custom label, and values.
Generates a report on TrueAlarm CO devices, including value and end-of-life date.
Generates a report containing Install Mode list information.
Reports on devices supporting alarm verification, including tally count.
To Next Page
