0478 403 9800 H - EN
24
– The entire machine is properly
assembled.
– The safety devices (e.g. self-propulsion
lever, impact protectors, protective
covers, handlebar, protective grille) are
in good condition and working properly.
Never use the machine with missing,
damaged or worn safety devices.
– The work tools (hoes), fastening bolts
and retaining pins are fitted and are not
worn or damaged (notches, cracks).
Worn or damaged parts must be
replaced.
– The work tools (hoes) are secure and
firmly installed.
– The self-propulsion levers are working
and are easy to operate.
– The tank cap is properly attached.
– The tank and fuel-carrying parts, as well
as the tank cap are in good condition.
– The oil closure screw is properly
attached.
– The accessories used are complete
and are properly installed on the
machine. All the components included
in the scope of delivery of the accessory
must be installed/used.
Carry out any necessary work or consult a
specialist dealer. VIKING recommends
VIKING specialist dealers.
The left and right impact protectors are
adapted to the relevant working width and
must always be properly installed. If, on
models HB 445 and HB 445 R, the
working width is increased using additional
hoes (VIKING accessories), the larger
impact protectors (supplied in the scope of
delivery of the accessories) must also be
installed.
Push or pull the machine to the area to be
worked with the aid of the transport
wheels.
Before operating, remove any foreign
objects (tools, cloths etc.) placed on the
machine.
4.6 Working with your machine
Keep other persons out of the
danger area. Never work when
animals or persons, particularly
children, are in the danger area.
Caution: Objects such as soil, stones etc.
can be thrown up or thrown out sideways
during working.
The machine may only be operated by one
person. The operator must stay within the
working area when the engine is running.
(Ö 10.1)
During operation, the machine must not be
lifted, pushed or pulled at the transport
handle, guard plate or at other machine
parts except for the handles of the
handlebar – and especially not by a
second person.
The switch and safety devices installed in
the machine must not be removed or
bypassed. In particular, never secure the
self-propulsion lever to the upper
handlebar (e.g. by tying it).
Caution – risk of injury!
Never put hands or feet on or
underneath rotating parts.
Always observe the safety
distance provided by the
handlebar. This safety distance
corresponds to the length of the properly
installed and folded-out handlebar. Do not
modify the handlebar and never operate
the machine with the handlebar folded
down.
Never attach any objects to the handlebar
(e.g. work clothing).
Only work during the day or with good
artificial light.
Do not operate the machine in the rain or
during thunder storms, particularly when
there is a risk of lightning strike.
The risk of accidents is higher if the ground
is damp due to increased danger of
slipping.
Particular caution should be exercised
during working in order to prevent slipping.
If possible, avoid using the machine when
the ground is damp.
Do not operate the machine on tarmac or
paved areas etc. with the hoes attached.
Exhaust gases:
The machine generates
poisonous exhaust gases when
the engine is running. The
gases contain poisonous
carbon monoxide, a colourless and
odourless gas, as well as other pollutants.
The engine must never be operated in
closed or poorly ventilated spaces.
Observe discharge direction of exhaust
gases. Never point the exhaust towards
persons.
Danger to life through poisoning!
In the case of nausea, headache,
impaired vision (e.g. decreasing
field of view) hearing disorder,
dizziness, decreasing power of
concentration, stop working
immediately. These symptoms may
be caused by excessively high
exhaust gas concentrations.
Ташев-Галвинг ООД
www.tashev-galving.com
To Next Page
Loading...
