10TA Service Manual
INDEX
5/30/14
12-1
12. Index
A
A Valves --------------------------------------------------------- 4-1, 5-1
Accumulator ----------------------------------------------------- 4-1, 5-1
Adding Refrigerant --------------------------------------------------- 5-4
Air - cooled Condenser Wiring (3 phase) -------------------- 3-12
Air-Cooled Condenser ---------------------------------------------- 9-5
Air-Cooled Condenser Data --------------------------------------- 3-9
Air-Cooled Condenser Installation ------------------------------- 3-7
Air-Cooled Piping Schematic -------------------------------------- 4-4
Air-Cooled Units ------------------------------------------------------ 9-5
Assembly Drawing , Air-Cooled --------------------- 1-4, 1-5, 1-6
Assembly Drawing , Water Cooled ----------------- 1-7, 1-8, 1-9
Automatic blowdown ------------------------------------------------ 9-1
B
Basic Product Warranty ------------------------- inside back cover
Bearing, Cutter ------------------------------------------------------- 9-19
Bill of Lading ----------------------------------------------------------- 2-1
Bin, Thermostat Installation--------------------------------------- 3-13
Bin, Thermostat Setup --------------------------------------------- 3-14
Blowdown -------------------------------------------------------------- 9-1
Burnout, Compressor ---------------------------------------------- 9-14
C
Capacity Ratings ---------------------------------------------------- 11-3
Capillary By-pass ----------------------------------------------------- 9-4
Charging Refrigeration Systems --------------------------------- 1-2
Check Valve ----------------------------------------------------------- 4-2
Checklist, Installation Review ------------------------------------ 3-15
Chemical Cleaning --------------------------------------------------- 7-5
Circuit Breaker, Control --------------------------- 6-2, 6-4, 6-5, 6-6
Circulating Water Pump / Motor --------------------------------- 9-17
Clean/Off/Ice Switch ------------------------------------- 6-1, 6-3. 6-4
Cleaning Procedure ------------------------------------------------- 7-1
Compressor ------------------------------------------------------------ 7-6
Compressor Crankcase Heater --------------------------------- 9-11
Compressor Lubrication -------------------------------------------- 7-6
Compressor Motor Burnout --------------------------------------- 9-14
Compressor Unloader ---------------------------------------------- 9-16
Compressor, Contactor --------------------------- 6-2, 6-4, 6-5. 6-6
Compressor, Motor Protection ------------------------------------ 9-6
Condenser Cleaning ------------------------------------------------- 9-5
Condenser Fan Contactor (FC) ---------------- 6-2, 6-4, 6-5. 6-6
Condenser Fan Switch ---------------------------------------------- 9-5
Condenser Piping (Cold Weather Valve Kit) ------------------ 3-9
Condenser Water Usage ----------------------------------------- 11-4
Condenser, Air-cooled Cleaning --------------------------------- 9-5
Condenser, Air-cooled Heat Rejection ------------------------- 3-8
Condenser, Pressure Switch (CPS) ----------------------------- 9-5
Condenser, Water Cooled ----------------------------------- 3-2, 7-4
Control Circuit Protection ------------------------------------------ 9-11
Control Panel / Parts ------------------------------------------ 6-5, 6-6
Control, Relay (CR) -------------------------------- 6-2, 6-4, 6-5, 6-6
Cooling Tower --------------------------------------------------------- 3-2
CoreSense ---------------------------------------------- 6-9, 9-10, 9-11
Crankcase Heater -------------------------------------------- 7-6, 9-11
Crushed Ice Production ------------------------------------------- 9-22
Cutter & Bearing Removal/Installation ------------------------ 9-19
Cutter Drive Parts -------------------------------------------------- 9-21
Cutter Gear Reducer --------------------------------- 7-7, 9-16, 9-17
Cutter Motor---------------------------------------------------------- 9-18
Cutter, Assembly --------------------------------------------------- 9-20
Cutter, Bearing ------------------------------------------------------ 9-19
Cutter, Bearing Support ------------------------------------------- 9-19
Cutter, Disc Assembly --------------------------------------------- 9-20
Cutter, Drive Parts ------------------------------------------------- 9-21
Cutter, Gear Reducer -------------------------------------- 9-17, 9-18
Cutter, Motor --------------------------------------------------------- 9-18
Cutter Assembly ---------------------------------------------------- 9-20
Cutter Parts (crushed Ice) ---------------------------------------- 9-22
Cutter Parts (cylinder ice) ---------------------------------------- 9-20
D
D Valve (Thawing Gas ) ------------------------------------ 4-1, 9-15
Drive gear ------------------------------------------------------------ 9-21
E
Electrical Connection ------------------------------------------------ 3-5
Electrical Schematic All Voltages 50-60 Hz. ------------------ 6-7
Electrical, Controls --------------------------------------------------- 6-1
Enclosure --------------------------------------------------------------- 6-1
Energy Saving --------------------------------------------------------- 1-1
Equivalent Feet Due To Friction -------------------------------- 3-11
F
Fan Contactor (FC) -------------------------------- 6-2, 6-4, 6-5, 6-6
Filter/Drier -------------------------------------------------------------- 4-1
Float Switch ------------------------------------------------------------ 9-2
Float Valve (Make-Up Water) ------------------------------------- 9-1
Freeze Period --------------------------------------------------------- 4-2
Freeze-Up Due To Extended Freezing Period --------------- 8-4
Freeze-Up Due To Ice Failing To Discharge ------------------ 8-5
Freezer ------------------------------------------------------------------ 4-1
Freezer Pressure Switch ------------------------------------------- 9-3
G
Gear Reducer ------------------------------------------------------- 9-17
H
Hand Expansion Valve ---------------------------------------------- 9-3
Harvest Period -------------------------------------------------------- 4-2
Head Pressure -------------------------------------------------------- 9-5
Heat Exchanger ------------------------------------------------------- 4-1
Heater, Crankcase ------------------------------------------------- 9-11
To Next Page
Loading...
