VTech VC7151-102A - Page 29

85 pages

Save Page as PDF

To Next Page

To Previous Page

After testing the sensor signal strength, mark the mounting location on the door,

window, drawer, cupboard or jewelry box and its respective frame. Then, remove

the adhesive tape and proceed to the mounting process.

NOTES

The door images in this installation guide are for conceptual reference only.

•

Main Page

Default Chapter2
- Important Safety Instructions2
- Save These Instructions3
- About Cordless Telephones4
- Table of Contents5
Introduction7
What's in the Box8
Overview11
- Handset Overview11
- Telephone Base Overview14
- Contact Sensor Overview18
- Sensor Unit Overview18
- Display Icons Overview19
- Lights Overview21
Installation Setup22
- Telephone Installation22
  - Install the Handset Battery23
  - Charge the Handset Battery23
Sensor Battery26
- Contact Sensor Installation27
Before Use34
- Set Date and Time34
- Check for Dial Tone34
- Operating Range34
Sensor35
- Arm/Disarm the Sensor Alert System36
- Sensor Mode37
- Edit Numbers for Remote Calls38
- Set Time Delay for Remote Calls38
- Access an Individual Sensor Menu40
- Set Alert Schedule as Always on41
- Set a Time Range for Alerts42
- Turn off the Alerts43
- Alert Notifications44
- Test Sensor Signal Strength45
- Rename the Sensor46
- Reset Sensor Alerts46
- Sensor Log47
Configure Your Telephone48
- Using the Menus48
- Set Voice Langauge48
- Set Date and Time48
- Quiet Mode49
- Synchronize the Date & Time with Calling Number Display Service49
- Dial Mode49
Telephone Operations50
- Make a Call50
- Answer a Call50
- End a Call50
- Handset Speakerphone50
- Volume50
- Mute51
- Call Waiting51
- Chain Dialing51
- Access a Number in the Phonebook While on a Call51
- Access a Number in the Caller ID Log While on a Call51
- Equalizer52
- Find Handset52
- Redial List52
- Save a Redial Entry to the Phonebook53
- Join a Call in Progress53
- One-Touch Broadcast (OTB)53
- Switch an OTB Communication to the Intercom Call54
- Turn the OTB Call on or off54
- Intercom54
- Share Call55
- Transfer a Call55
- Answer an Incoming Call During an Intercom Call55
Phonebook56
- Add a Phonebook Entry56
- Review and Dial from the Phonebook57
- Edit a Phonebook Entry57
- Delete a Phonebook Entry57
Caller ID58
- Caller ID Log58
- Review and Dial a Number in the Caller ID Log58
- Save a Caller ID Log Entry to the Phonebook58
- Delete a Caller ID Log Entry58
- Delete All Caller ID Log Entries59
Call Block60
- Block Unknown Calls60
- Add a Call Block List Entry60
- Review the Call Block List61
- Edit a Call Block List Entry61
- Save a Caller ID Log Entry to Call Block List61
- Delete a Call Block List Entry61
Sound Settings62
- Key Tone62
- Ringer Tone62
- Ringer Volume62
- Temporary Ringer Silencing63
About the Built-In Answering System and Voicemail Service64
Set Your Built-In Answering System65
- Turn the Answering System on or off65
- Default Announcement65
- Record Your Own Announcement66
- Play the Announcement66
- Reset the Announcement66
- Set Number of Rings67
- Message Alert Tone67
- Recording Time68
Use Your Built-In Answering System69
- New Message Indication69
- Message Playback69
- Delete All Old Messages70
- Call Intercept70
- Call Screening70
Remote Access71
- Listen to Messages from Remote Access71
- Change Sensor Mode from Remote Access72
- Remote Access Code72
Use the Built-In Answering System and Voicemail Service73
Retrieve Voicemail from Telephone Service73
- Retrieve Voicemail73
- Set Your Voicemail Number73
- Turn off the New Voicemail Indicators74
Add a New Handset75
Add a New Sensor76
Deregister the Sensor77
ECO Mode78
General Product Care78
Storage79
Frequently Asked Questions80
Technical Specifications83
Disclaimer84

VTech VC7151-102A - Page 29

Table of Contents

Related product manuals