Safety Information
We use note, caution and warning symbols through-
out this book to draw your attention to important
operational and safety information.
A “NOTE” marks a short message to alert you to
an important detail.
A “CAUTION” safety alert appears with informa-
tion that is important for protecting your equip-
ment and performance. Be especially careful to
read and follow all cautions that apply to your
application.
A “WARNING” safety alert appears with infor-
mation that is important for protecting you, oth-
ers and equipment from damage. Pay very close
attention to all warnings that apply to your
application.
The electrical hazard symbol,
Ó
(a lightning bolt
in a triangle) precedes an electric shock hazard
CAUTION or WARNING safety statement.
Symbol Explanation
CAUTION – Warning or Hazard
that needs further explanation
than label on unit can provide.
Consult users manual for further
information.
ESD Sensitive product, use proper
grounding and handling tech-
niques when installing or servic-
ing product.
Unit protected by double/rein-
forced insulation for shock hazard
prevention.
Do not throw in trash, use proper
recycling techniques or consult
manufacturer for proper disposal.
Enclosure made of Polycarbonate
material. Use proper recycling
techniques or consult manufac-
turer for proper disposal.
Unit can be powered with either
alternating current (ac) voltage or
direct current (dc) voltage.
Unit is a Listed device per Un-
derwriters Laboratories®. It has
been evaluated to United States
and Canadian requirements for
Process Control Equipment. UL
61010 and CSA C22.2 No. 61010.
File E185611 QUYX, QUYX7.
See: www.ul.com
Unit is a Listed device per Un-
derwriters Laboratories®. It has
been evaluated to United States
and Canadian requirements for
Hazardous Locations Class 1
Division II Groups A, B, C and
D. ANSI/ISA 12.12.01-2007. File
E184390 QUZW, QUZW7. See:
www.ul.com
Unit is compliant with European
Union directives. See Declaration
of Conformity for further details
on Directives and Standards used
for Compliance.
Unit has been reviewed and ap-
proved by Factory Mutual as a
Temperature Limit Device per FM
Class 3545 standard. See: www.
fmglobal.com
Unit has been reviewed and ap-
proved by CSA International for
use as Temperature Indicating-
Regulating Equipment per CSA
C22.2 No. 24. See: www.csa-inter-
national.org
Unit has been reviewed and ap-
proved by ODVA for compliance
with DeviceNet communications
protocol. See: www.odva.org
Unit has been reviewed and ap-
proved by ODVA for compliance
with Ethernet/IP communications
protocol. See: www.odva.org
Warranty
The EZ-ZONE
®
PM is manufactured by ISO
9001-registered processes and is backed by a three-
year warranty to the first purchaser for use, provid-
ing that the units have not been misapplied. Since
Watlow has no control over their use, and sometimes
misuse, we cannot guarantee against failure. Wat-
low’s obligations hereunder, at Watlow’s option, are
limited to replacement, repair or refund of purchase
price, and parts which upon examination prove to be
defective within the warranty period specified. This
warranty does not apply to damage resulting from
transportation, alteration, misuse or abuse. The pur-
chaser must use Watlow parts to maintain all listed
ratings.
Technical Assistance
If you encounter a problem with your Watlow control-
ler, review your configuration information to verify
that your selections are consistent with your applica-
tion: inputs, outputs, alarms, limits, etc. If the prob-
lem persists, you can get technical assistance from
your local Watlow representative (see back cover), by
e-mailing your questions to wintechsupport@watlow.
com or by dialing +1 (507) 494-5656 between 7 a.m.
and 5 p.m., Central Standard Time (CST). Ask for for
an Applications Engineer. Please have the following
information available when calling:
• Complete model number
To Next Page
Loading...
