To Next PageTo Next PageWhy Yamaha DSP-AZ1 sound field parameters cannot be changed?
If you cannot change the sound field parameters and some other settings on your Yamaha Amplifier, check if “16 MEMORY GUARD” on the SET MENU is set to “ON”. If so, select “OFF”.
What does “CHECK SP WIRES” mean on my Yamaha Amplifier?
If “CHECK SP WIRES” appears on the front panel display of your Yamaha Amplifier, it indicates that the speaker cables are short-circuited. Ensure all speaker cables are connected correctly.
What to do if Yamaha Amplifier fails to turn on?
If your Yamaha Amplifier fails to turn on, ensure the power cord is firmly connected. If the IMPEDANCE SELECTOR on the rear panel is not fully set, adjust it to the upper or lower position. Check all speaker wire connections to ensure they are secure and not touching anything other than their respective connections. If the unit has been exposed to a strong electric shock, set it to standby mode, disconnect the power cord, wait 30 seconds, and then plug it back in.
Why Yamaha DSP-AZ1 has no sound from the effect speakers?
If there is no sound from the effect speakers on your Yamaha Amplifier, and “STEREO” is shown in the front panel display, it means the input source is being played with normal stereo reproduction. Press STEREO/EFFECT to turn on the sound effect.
Why Yamaha DSP-AZ1 has no sound from the rear speakers?
If there is no sound from the rear speakers of your Yamaha Amplifier, check that “1C REAR L/R SP” on the SET MENU is not set to “NONE”. Select the appropriate speaker mode for the rear L/R speakers. If a monaural source is being played with the program 12, select another DSP program.
Why Yamaha Amplifier has no sound from the center speaker?
If there is no sound from the center speaker of your Yamaha Amplifier, check that “1A CENTER SP” on the SET MENU is not set to “NONE”. Select the appropriate mode for your center speaker. Also, if one of the Hi-Fi DSP programs (1 to 6 except for Game and 8ch Stereo) is selected, try selecting another DSP program.
Why Yamaha DSP-AZ1 has poor bass reproduction?
If your Yamaha Amplifier has poor bass reproduction, and “1E LFE/BASS OUT” on the SET MENU is set to “SW” or “BOTH” but you don't have a subwoofer, select “MAIN”. Also, ensure the output mode for each speaker (main, center, rear, or rear center) on the SET MENU matches your speaker configuration; adjust as necessary based on speaker sizes.
Why Yamaha DSP-AZ1 has no sound from the subwoofer?
If there's no sound from the subwoofer on your Yamaha Amplifier, and a Dolby Digital or DTS signal is playing, ensure that “1E LFE/BASS OUT” on the SET MENU is set to “SW” or “BOTH”. If a 2-channel source is playing, select “BOTH”.
Why Yamaha DSP-AZ1 Amplifier on-screen display does not appear?
If the on-screen display does not appear on your Yamaha Amplifier, check if the display setting is set to “DISPLAY OFF”. If so, select the full display or short display mode. Also, if the BLUE BACK setting under “15 DISPLAY SET” on the SET MENU is set to “OFF” and no video signal is input, set BLUE BACK to “AUTO” to always show the OSD.
What to do if Yamaha DSP-AZ1 only the speaker on one side can be heard?
If you only hear sound from one speaker with your Yamaha Amplifier, check the cable connections to ensure they are properly connected; if the problem continues, the cables may be defective. Also, verify that the BALANCE setting is not turned to the extreme left or right; adjust it to the appropriate position.
General| Channels | 7.1 |
|---|---|
| Total Harmonic Distortion | 0.04% |
| Signal-to-Noise Ratio | 100 dB |
| Input Sensitivity | 200 mV |
| Power Output | 140 W per channel (8 ohms) |
| Frequency Response | 10 Hz - 100 kHz |
| Surround Sound Formats | Dolby Digital, DTS, Dolby Pro Logic II |
| Speaker Load Impedance | 8 ohms |
| Video Inputs/Outputs | Composite, S-Video, Component |
Details the technical specifications and advanced capabilities of the AV amplifier.
Explains the various buttons and controls on the front panel and remote.
Guides on setting up speaker configurations for optimal sound.
Instructions on positioning main, center, and surround speakers for best acoustics.
Details on connecting various audio and video components to the unit.
How to use the on-screen display for settings and information.
Steps for turning on the unit, selecting sources, and playing audio/video.
Instructions on how to record audio and video from one source to another.
Comprehensive list and explanation of the unit's configurable menu settings.
Information on using the remote control for the main unit and other components.
Guide to adjusting volume levels for center, surround, and effect speakers.
How to set the unit to automatically switch to standby mode after a specified time.
Explanation of how sound fields are created and their characteristics.
Details on sound field programs suitable for stereo music sources like CDs.
Information on programs designed to recreate movie theater sound experiences.
How to adjust sound field parameters to suit your listening environment.
Solutions for common operational problems and error messages.
Technical details and performance characteristics of the AV amplifier.
