Yamaha HTR-3068 User Manual

En 104
Audio
Problem Cause Remedy
No sound.
Another input source is selected. Select an appropriate input source with the input selection keys.
Signals that the unit cannot reproduce are being input.
Some digital audio formats cannot be played back on the unit. To check the audio
format of the input signal, use “Signal Info” in the “Option” menu (p.74).
(RX-V579 only)
Audio output to Zone A (or Zone B) is disabled.
Press ZONE A (ZONE B) to enable audio output to Zone A (or Zone B).
The cable connecting the unit and playback device is defective. If there is no problem with the connection, replace with another cable.
The volume cannot be increased.
The maximum volume is set. Use “Max Volume” in the “Setup” menu to adjust the maximum volume (p.87).
A device connected to the output jacks of the unit is not turned on.
(This may happen due to the nature of AV receivers.)
Turn on all devices connected to the output jacks of the unit.
No sound is coming from a specific speaker.
The playback source does not contain a signal for the channel. To check it, use “Signal Info” in the “Option” menu (p.74).
The currently selected sound program/decoder does not use the
speaker.
To check it, use “Test Tone” in the “Setup” menu (p.83).
Audio output of the speaker is disabled.
Perform YPAO (p.28) or use “Configuration” in the “Setup” menu to change the
speaker settings (p.80).
The volume of the speaker is set too low.
Perform YPAO (p.28) or use “Level” in the “Setup” menu to adjust the speaker
volume (p.82).
(RX-V579 only)
Audio output to Zone A (or Zone B) is disabled.
Press ZONE A (ZONE B) to enable audio output to Zone A (or Zone B).
The speaker cable connecting the unit and the speaker is
defective.
If there is no problem with the connection, replace with another speaker cable.
The speaker is malfunctioning.
To check it, replace with another speaker. If the problem persists, the unit may be
malfunctioning.
(RX-V579 only)
No sound is coming from the surround back
speaker.
The extended surround is disabled.
Use “Extended Surround” in the “Option” menu to select a decoder to be used
(p.73).
“Power Amp Assign” is set to “BI-AMP” or “Zone B”.
When “Power Amp Assign” in the “Setup” menu is set to “BI-AMP” or “Zone B”,
you cannot use the surround back speakers. To use the surround back speakers,
set “Power Amp Assign” to “Basic” (p.80).
No sound is coming from the subwoofer.
The playback source does not contain Low Frequency Effect (LFE)
or low-frequency signals.
To check it, set “Extra Bass” in the “Setup” menu to “On”, in order to output the
front channel low-frequency components from the subwoofer (p.81).
Subwoofer output is disabled. Perform YPAO (p.28) or set “Subwoofer” in the “Setup” menu to “Use” (p.80).
The volume of the subwoofer is too low. Adjust the volume on the subwoofer.
The subwoofer has been turned off by its auto-standby function. Disable the auto-standby function of the subwoofer or adjust its sensitivity level.
00_RX-V479_V579_om_U.book Page 104 Wednesday, March 25, 2015 9:59 AM

Yamaha HTR-3068 Specifications

General

Receiver type	Surround
Pre-out channels	1 SW
Pre-out connectivity	Yes
Audio output channels	5.1 channels
Total Harmonic Distortion (THD)	0.09 %
Dynamic power per channel (4 Ohm)	130 W
Power output per channel (1KHz@6 Ohm)	110 W
Power output per channel (20-20KHz@8 Ohm)	70 W
HDMI in	4
Audio (L/R) in	3
Composite video in	1
Digital audio coaxial in	2
Connectivity technology	Wireless
Speakers connectivity type	-
Ethernet LAN	No
Supported radio bands	AM, FM
Product color	Black
Audio decoders	DTS-HD Master Audio, Dolby Digital Plus, Dolby TrueHD
Sustainability certificates	ENERGY STAR
Power consumption (standby)	0.3 W

Weight and Dimensions

Depth	315 mm
Width	435 mm
Height	151 mm
Weight	7400 g