P-85/P-85S
48
MIDI DATA FORMAT
SEGASSEMEDOM.3FFO/NOETON.1
Data format: [9nH] -> [kkH] -> [vvH] Data format: [BnH] -> [ccH] -> [vvH]
9nH = Note ON/OFF event (n = channel number) BnH = Control event (n = channel number)
kkH = Note number (Transmit: 09H–78H = A-2–C8 / ccH = Control number
Receive: 00H-7FH = C-2–G8) vvH = Data Range
vvH = Velocit
y (Key ON = 01H–7FH, Key OFF = 00H)
(1) All Sound Off
Data format: [8nH] -> [kkH] -> [vvH] (reception only) ccH Parameter Data Range (vvH)
8nH = Note OFF event (n = channel number) 78H All Sound Off 00H
kkH = Note number: 00H–7FH = C-2–G8)
vvH = Velocity
(2) Reset All Controllers
ccH Parameter Data Range (vvH)
2. CONTROL CHANGE
79H Reset All Controllers 00H
Data format: [BnH] -> [ccH] -> [vvH] Resets controllers as follows.
BnH = Control change (n = channel number) Controller Value
ccH = Control numbe
r Expression 127 (max)
vvH = Data Rang 0ladePniatsuSe (off)
Sostenuto 0 (off)
(1) Bank Select
Soft Pedal 0 (off)
ccH Parameter Data Range (vvH)
00H Bank Select MSB 00H:Normal
(3) Local Control (reception only)
naRataDretemaraPHccHF7...H00BSLtcel
eSknaBH02 ge (vvH)
Bank selection processing does not occur until receipt of 7AH Local Control 00H (off), 7FH (on)
next Program Change message.
(4) All Notes Off
(2) Main Volume
ccH Parameter Data Range (vvH)
ccH Parameter Data Range (vvH) 7BH All Notes Off 00H
ltnerruceratahtsetonehtllaFFOsehctiwSHF7...H00BSMemuloVH70 y ON on the
specified channel. Any notes being held by the sustain or
(3) Expression (reception only)
sostenuto pedal will continue to sound until the pedal is
ccH Parameter Data Range (vvH) released.
0BH Expression MSB 00H...7FH
(5) Omni Off (reception only)
(4) Sustain
ccH Parameter Data Range (vvH)
ccH Parameter Data Range (vvH) 7CH Omni Off 00H
emaSHF7...H00BSMni
atsuSH04 processing as for All Notes Off.
(5) Sostenuto (6) Omni On (reception only)
ccH Parameter Data Range (vvH) ccH Parameter Data Range (vvH)
42H Sostenuto 00H...3FH:off, 40H...7FH:on 7DH Omni On 00H
Same processing as for All Notes Off.
(6) Soft Pedal
ccH Parameter Data Range (vvH)
(7) Mono (reception only)
43H Soft Pedal 00H...3FH:off, 40H...7FH:on ccH Parameter Data Range (vvH)
7EH Mono 00H
(7) Effect1 Depth (Reverb Send Level)
Same processing as for All Sound Off.
ccH Parameter Data Range (vvH)
5BH Effect1 Depth 00H...7FH
(8) Poly (reception only)
Adj naRataDretemaraPHcc.leveldnesbreverehtstsu ge (vvH)
7FH Poly 00H
(8) Effect4 Depth (Variation Effect Send Level)
Same processing as for All Sound Off.
ccH Parameter Data Range (vvH)
5EH Effect4 Dep nahClortnoCnehW•HF7...H00ht ge is turned OFF, Control Change messages
will not be transmitted or received.
(9) RPN
• Local on/off, OMNI on/off are not transmitted. (The appropriate
ussirebmunffoetonBSMNPRH56 pplied with “All Note Off” transmission).
deviecersiBSL/BSMknabeciovanehW•BSLNPRH46 , the number is stored
06H Data Entry erreffublanretniehtniBSM gardless of the received order, then the
26H Data Entry aehttc
elesotdesusieulavderotsBSL ppropriate voice when a
60H Data Increment program change message is received.
loP•tnemerceDataDH16 y mode is always active. This mode will not change when the
assemedomYLOP/ONOMaseviecertnemurtsni:NPRhtiwelballo
rtnoceratahtsretemaraP* ge.
• Coarse Tune
• Fine Tune
• Pitch Bend Range
If you’re already very familiar with MIDI, or are using a computer to control your music hardware with computer-generated MIDI messages,
the data provided in this section can help you to control the P-85.
To Next Page
Loading...
