Yamaha P-85 - Page 50

P-85/P-85S
50
8. SYSTEM EXCLUSIVE MESSAGES (XG Standard) 10. SYSTEM EXCLUSIVE MESSAGES (Special Control)
Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [11H] ->
(1) XG Native Parameter Change
[0nH] -> [ccH] -> [vvH] -> [F7H]
Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] -> F0H = Exclusive status
[mmH] -> [llH] -> [ddH] -> [F7H] 43H = Yamaha ID
iD=H37sutatsevisulcxE=H0F gital Piano ID
DItcudorPdednetxE=HF7DIAHAMAY=H34
1nH = When received, DItcudorP=HB4.F–0=n
When transmitted, S=H11.0=n pecial control
nahcIDIM
lortnoC=Hn0GXfoDIledoM=HC4
ge (n=channel number)
hhH = Address Hig rebmunlortnoC=cch
mmH
= eulaV=vvdiMsserddA
evisulcxEfodnE=H7FwoLsserddA=Hll
ddH = Data
|
Control Channel ccH vvH
n
uteDlennahCevisulcxEfodnE=H7F ech: 00H–0FH 43H (Sets the Detune value
for each channel
)
Data size must match parameter size (2 or 4 bytes) HF7–H00.
When the XG System On message is received, the MIDI Voice Reserve ch: 00H–0FH 45H 00H : Reserve off
s
ystem will be reset to its default setting *no:HF7.s
The message requires approximately 50ms to execute, so * When Volume, Expression is received for Reserve On,
sufficient time should be allowed before the next message is they will be effective from the next Key On. Reserve Off
.lamronsi.tnes
(2) XG Native Bulk Data (reception only) 11. SYSTEM EXCLUSIVE MESSAGES (Others)
Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] -> Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] ->
[bbH] -> [hhH] -> [mmH] -> [llH] -> [ddH] ->...-> [00H] -> [00H] -> [mmH] -> [llH] -> [ccH] ->
[ccH] -> [F7H] [F7H]
ninuTretsaMsutatsevisulcxE=H0
F g (XG and last message priority)
lsuoenatlumisDIAHAMAY=H34
y changes the pitch of all channels.
0nH = When received, n=0–F.
When transmitted
,sutatSevisulcxE=H0F.0=n
DIahamaY=H34GXfoDIledoM=HC4
aaH = ByteCount 1nH = When received, n=0–F.
bbH = B
yteCount When transmitted, n=0.
hhH = Address Hig 001GTfoDIledoM=H72
h
mmH
= DIbuS=H03diMsserddA
=H00woLsserddA=Hll
=H00ataD=Hdd
|| Hmm =Master Tune MSB
|| BSLenuTretsaM=Hll
tnavelerri=HccmuskcehC=Hcc (under 7FH)
e
visulcxEfodnE=H7FevisulcxEfodnE=H7F
• Receipt of the XG SYSTEM ON message causes
reinitialization of relevant
parameters and Control Change
values. Allow sufficient time for processing to execute
(about 50 msec) before sending the P-85 another message.
• XG Native Parameter Change message may contain two or
four bytes of parameter data (depending on the parameter
size).
• For information about the Address and Byte Count values,
refer to Table 1 below. Note that the table’s Total Size value
gives the size of a bulk block. Only the top address of the
block (00H, 00H, 00H) is valid as a bulk data address.
9. SYSTEM EXCLUSIVE MESSAGES
(Digital Piano MIDI Format)
Data format: [F0H] -> [43H] -> [73H] -> [01H] -> [xxH] -> [F7H]
F0H = Exclusive status
43H = Yamaha ID
73H = Digital Piano ID
01H = Product ID (digital piano common)
xxH = Substatus
nn Control
02H Internal MIDI clock
03H External MIDI clock
06H Bulk Data
(the bulk data follows 06H)
F7H = End of Exclusive