YASKAWA CIMR-ACA4011 - Defaults for Various MXC Capacities (O2-04)

Parameter Tables
5-65
* 1. These are setting range and default value for a 200 V class MxC. Values for a 400 V class MxC are double.
* 2. Settings vary as shown in the following tables depending on the MxC capacity and E1-03.
200 V and 400 V Class MxCs of 5.5 to 75 kW
* The setting shown are for 200 V class MxCs. The values will double for 400 V class MxCs.
 Defaults for Various MxC Capacities (o2-04)
If the MxC capacity (o2-04) is changed, the defaults of the following parameters will change.
* Under development.
F1-09
Overspeed Detection Delay Time
0.0 to 2.0 0.1 s - - 0.0
PG Overspd Time
Parameter
Number
Unit
Default
Open
Loop
Vector
Control
Flux
Vector
Control
E1-03
-0123456789ABCDF
E1-04 Hz
50.0 60.0 60.0 72.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 90.0 120.0 60.0 60.0 60.0
E1-05 * V
200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0
E1-06 Hz
50.0 60.0 50.0 60.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 60.0 60.0 60.0 60.0 0.0
E1-07 Hz
2.5 3.0 3.0 3.0 25.0 25.0 30.0 30.0 2.5 2.5 3.0 3.0 3.0 3.0 3.0 3.0 0.0
E1-08 * V
14.0 14.0 14.0 14.0 35.0 50.0 35.0 50.0 18.0 23.0 18.0 23.0 14.0 14.0 14.0 13.0 0.0
E1-09 Hz
1.3 1.5 1.5 1.5 1.3 1.3 1.5 1.5 1.3 1.3 1.5 1.5 1.5 1.5 1.5 0.5 0.0
E1-10 * V
7.0 7.0 7.0 7.0 6.0 7.0 6.0 7.0 9.0 11.0 9.0 13.0 7.0 7.0 7.0 2.5 0.0
Parameter
Number
Name Unit
Default
200 V class 400 V class
- MxC Capacity
kW 5.5 11 22 45 5.5 11 22
45 75
*
E2-11 Motor Rated Output
E4-07 Motor 2 Rated Output
o2-04 MxC/kVA Selection - 5 7 A D 26 28 2B 2E 30
E2-01
(E4-01)
Motor Rated Current A 19.60 39.7 77.2 160.0 9.80 19.9 38.6 79.7 130.0
E2-02
(E4-02)
Motor Rated Slip Hz 1.50 1.70 1.70 1.60 1.50 1.70 1.70 1.60 1.39
E2-03
(E4-03)
Motor No-Load Current A 5.10 11.2 18.5 44.0 2.60 5.6 9.2 22.0 36.0
E2-05
(E4-05)
Motor Line-to-Line Resistance Ω 0.399 0.230 0.079 0.030 1.595 0.922 0.316 0.122 0.092
E2-06
(E4-06)
Motor Leakage Inductance % 18.2 19.5 19.5 20.2 18.2 19.6 23.5 19.9 20.0
E2-10
Motor Iron Loss for Torque Compen-
sation
W 172 245 538 852 193 385 586 1125 1600
L2-03
Momentary Power Loss Minimum
Base Block Time
s 0.7 0.9 1.1 0.387 0.7 0.9 1.1 0.387 0.533
L8-02 Overheat Alarm Level °C 90 90 85 1.2 85 85 85 1.2 1.5
n5-02 Motor Acceleration Time s 0.168 0.265 0.355 90 0.168 0.265 0.355 90 90
Parameter
Number
Name
Setting Range Unit
Default
Display
V/f
Control
Open loop
Vector
Flux
Vector