YOKOGAWA AXFA14C User Manual

8. Parameter Summary
NOTE
For FOUNDATIONeldbusprotocol,refertoIM
01E20F02-01E. For PROFIBUS PA protocol, refer to
IM 01E20F12-01E. For HART protocol, refer to the
applicable user’s manuals which can be downloaded
from our website.
IMPORTANT
Make sure to keep the instrument’s power on at least
for 30 seconds after you set the parameters.
If you turn the power off immediately after the
parameters are set, the settings will be canceled.
8.1 Menu tree for DD (HART 5)
Ofinemenu
NewConguration
SavedConguration
Online menu
R/W (*3)
Parameter No.
(BRAIN protocol)
Data (*4)
Device setup
Process Variables PV % rnge R A10 P
PV PV R A20 P
PV AO PV AO R A21 P
PV Span Totl R A30 P
Reverse Totl R A31 P
Dif Totl R A32 P
Diag/Service
Test/Status Status Status group 1(System alarms) R
See Chapter 7
-
Status group 3(Process alarms) R -
Status group 5(Setting alarms) R -
Status group 6(Setting alarms) R -
Status group 7(Setting alarms) R -
Status group 8(Warnings) R -
Self test W - -
Adjustment
Auto Zero Exe W M10/B50 -
MagowZero R/W M11 -
D/A trim W - -
Scaled D/A trim W - -
Output Test
Loop test 4mA W - -
20mA W - -
Other W - -
End W - -
Test Mode W N10 -
Test SO1 (*1) W N20 -
Test SO2 (*1) W N21 -
Test Alarm Out (*1) W N22 -
Test SI1 (*1) R N23 P
Test SI2 (*1) R N24 P
Test DO (*2) W N30 -
Test DIO (O) (*2) W N31 -
Test DIO (I) (*2) R N32 P
Diagnosis
Adhesion Check W K10 -
Adhesion Level1 W K11 -
Adhesion Level2 W K12 -
Adhesion Level3 W K13 -
Adhesion Level4 W K14 -
Adh Measure Value R K15 -
Easy Setup
Language W B10/H30 u/d
PV Damping W B20/C11 u/d
Base Flow Unit W B21/C40 u/d
Base Time Unit W B22/C41 u/d
PV Span W B23/C42 u/d
Flow Decimal Pnt W B24/C43 u/d
Total Unit W B30/D10 u/d
Total Scale W B31/D11 u/d
Pulse Unit W B32/E10 u/d
Pulse Scale W B33/E11 u/d
Display Select1 W B40/H10 u/d
Display Select2 W B41/H11 u/d
Display Select3 W B42/H12 u/d
Auto Zero Exe W B50/M10 -
Detailed Setup
Basic Setup Tag W C10 u/d
PV Damping W C11/B20 u/d
MF Set
Standard DF W C20 -
Low MF W C21 -
High MF W C22 -
Enhanced DF W C20 -
Low MF (EDF) W C23 -
High MF (EDF) W C24 -
Select Flow Tube (*1) W C30 -
Nominal Size unit W C31 u/d
Nominal Size W C32 u/d
Base Flow Unit W C40/B21 u/d
Base Time Unit W C41/B22 u/d
PV Span W C42/B23 u/d
Flow Decimal Pnt W C43/B24 u/d
Velocity Check R C44 P
Density Unit W C45 u/d
Mass Flow Density W C46 u/d
User Span Select W C47 u/d
Flow User Unit W C48 u/d
Flow User Span W C49 u/d
*1 : Applicable for AXFA11 Remote Converter.
*2 : Applicable for AXF Integral Flowmeter and
AXFA14 Remote Converter.
*3 : R/W : R = Read only, W = Read and Write
*4 : Data Renewing
P : Periodic Data Renewing
u/d : Discretionary Renewing
– : Others (Method etc...)
Total
Total Unit W D10/B30 u/d
Total Scale W D11/B31 u/d
Total Decimal Pnt W D12 u/d
Total Low Cut W D13 u/d
Total Execution W D20 u/d
Ttl Set Val Lower W D21 u/d
Ttl Set Val Upper W D22 u/d
Ttl Switch Lower W D23 u/d
Ttl Switch Upper W D24 u/d
Ttl User Select W D30 u/d
Ttl User Unit W D31 u/d
Pulse
Pulse Unit W E10/B32 u/d
Pulse Scale W E11/B33 u/d
Pulse Width W E12 u/d
Pulse Low Cut W E13 u/d
Pulse Active Mode (*1) W E20 u/d
(continued on next page)
<8. Parameter Summary>
64
IM 01E20A01-01EN

YOKOGAWA AXFA14C Specifications

General

Brand	YOKOGAWA
Model	AXFA14C
Category	Measuring Instruments
Language	English