YOKOGAWA DLM3054 - User Manual

Questions and Answers

C
cortezgailAug 14, 2025
Why are the measured values not correct on my YOKOGAWA Test Equipment?
- K
  kingrobertAug 15, 2025
  Incorrect measured values on your YOKOGAWA Test Equipment can stem from several causes. First, ensure the instrument warms up for 30 minutes after powering on. Then, calibrate the instrument. Also, verify that the probe's phase has been corrected properly and the probe attenuation is set to an appropriate value. Finally, confirm that the offset voltage is set to 0 V. If problems persist, recalibrate the instrument; further issues may require servicing.
R
Randy WarnerAug 18, 2025
What to do if my YOKOGAWA DLM3054 Test Equipment is not triggering?
- M
  melindafreemanAug 18, 2025
  If triggering is not working on your YOKOGAWA Test Equipment, the trigger settings may not be appropriate. Ensure you set the trigger conditions correctly.
C
charleshallAug 21, 2025
What to do if my YOKOGAWA DLM3054 does not turn on?
- P
  prubioAug 21, 2025
  If your YOKOGAWA Test Equipment does not turn on, it might be due to using a power supply outside the specified ratings. Make sure to use a correct power supply.
E
epattersonAug 25, 2025
What to do if I cannot save to the specified storage device with my YOKOGAWA DLM3054 Test Equipment?
- E
  Emma TaylorAug 26, 2025
  If you cannot save to the specified storage device with your YOKOGAWA Test Equipment, it could be due to the storage device not being formatted. In this case, format the storage device. Alternatively, the storage device might be full. Try deleting unneeded files or using another storage device.
K
Kathleen CruzAug 28, 2025
What to do if nothing is displayed on my YOKOGAWA DLM3054 Test Equipment?
- E
  Edwin MurrayAug 28, 2025
  If nothing is displayed on your YOKOGAWA Test Equipment, first check if the backlight is turned off. If it is, press any key. If the screen displays inappropriate colors, turn the power off, and then turn the power on again while pressing RESET.
W
William ZunigaAug 31, 2025
How to fix odd display on YOKOGAWA Test Equipment?
- K
  Kristi CareyAug 31, 2025
  If the display on your YOKOGAWA Test Equipment appears odd, it could indicate that the system is not operating properly. Try turning off the instrument and then turning it back on.
S
swhiteSep 4, 2025
Why I am unable to configure or control the YOKOGAWA DLM3054 through the communication interface?
- A
  Amanda BakerSep 4, 2025
  If you are unable to configure or control the YOKOGAWA Test Equipment through the communication interface, the instrument’s address used by the program may be different from the specified address. Match the address used in the program to the instrument’s address. Also, the interface may not be used in a way that conforms to the electrical or mechanical specifications. Use the interface in a way that conforms to the specifications.
R
Richard OwenSep 7, 2025
What to do if keys do not work on YOKOGAWA DLM3054 Test Equipment?
- Y
  ythomasSep 7, 2025
  If the keys on your YOKOGAWA Test Equipment do not work, perform a key test. If the test fails, servicing is required.
K
Karen SingletonSep 10, 2025
Why I cannot print to the built-in printer on my YOKOGAWA Test Equipment?
- A
  Alexandria ThomasSep 10, 2025
  If you cannot print to the built-in printer on your YOKOGAWA Test Equipment, the printer head may be damaged or worn out, requiring servicing.

YOKOGAWA DLM3054 Specifications

General

Model	DLM3054
Bandwidth	500 MHz
Channels	4
Sampling Rate	2.5 GS/s
Display Size	10.4 inch
Display Type	TFT LCD
Vertical Sensitivity	1 mV/div to 10 V/div
Category	Oscilloscope
Type	Digital
Input Impedance	1 MΩ
Trigger Types	Edge, Pulse Width, Video, Window
Interface	USB, LAN
Power Supply	AC 100 V to 240 V