To Next Page

To Previous Page

App-14

IM DLM3054-01EN

Appendix 7 Firmware Version and New Features

The following table contains new features that are available for each firmware version. If you are using an older

version, you will not be able to use all the features described in this manual. To view the firmware version,

press the Overview soft key on the UTILITY menu and check Firmware Version on the Overview screen that is

displayed.

Version Suffix Code New Features Manual Edition Number

1.00 and later Standard New 1st Edition

Appendix

Default Chapter3
- Manuals3
- Table of Contents4
1 Vertical Axis (Analog Signal)10
- Turning the Display on and off (Display)10
- Vertical Scale (SCALE Knob)10
- Waveform Vertical Position (POSITION Knob)11
- Input Coupling (Coupling)12
- Probe Attenuation (Probe)12
- Inverted Waveform Display (Invert)13
- Linear Scaling (Linearscale)13
- Label Display (Label)14
- Bandwidth Limit (Bandwidth)14
- Offset (Offset)14
2 Vertical Axis (Logic Signal)16
- Turning the Display on and off (Display)16
- Vertical Display Range (SCALE Knob)16
- Vertical Position (POSITION Knob)16
- Setting the Bits (Bit Setup)16
- Bus Display (Bus)18
- State Display (State)19
- Setting the Display Order of Bits and the Bus (Bit Order)20
- Deskew (Deskew)20
3 Horizontal Axis (Time Axis)21
- Time Scale (TIME/DIV Knob)21
4 Triggering23
- Trigger Mode (Trigger Mode)23
- Trigger Type (Type)24
- Signal Type and Trigger Type Combinations25
- Basic Trigger Settings26
- Edge Trigger [EDGE]26
- Edge or Trigger [ENHANCED]30
- Pattern Trigger [ENHANCED]31
- Pulse Width Trigger [ENHANCED]35
- Rise/Fall Time Trigger [ENHANCED]36
- Runt Trigger [ENHANCED]38
- Timeout Trigger [ENHANCED]39
- Window Trigger [ENHANCED]40
- Window or Trigger [ENHANCED]42
- Interval Trigger [ENHANCED]43
- Serial Bus Trigger [ENHANCED]45
- Flexray Bus Trigger [ENHANCED, Option]46
- CAN Bus Trigger [ENHANCED, Option]52
- CAN FD Bus Trigger [ENHANCED, Option]60
- LIN Bus Trigger [ENHANCED, Option]66
- CXPI Bus Trigger [ENHANCED, Option]70
- SENT Trigger [ENHANCED, Option]78
- UART Trigger [ENHANCED, Option]84
- I 2 C Bus Trigger [ENHANCED, Option]86
- SPI Bus Trigger [ENHANCED, Option]91
- User-Defined Serial Bus Trigger [User Define, ENHANCED]94
- TV Trigger [ENHANCED]96
- Trigger B [B TRIG]99
5 Executing Actions101
- Action Mode (Mode)101
- Action to Execute When Conditions Are Met (Action)101
- Number of Actions (Action Count/Nogo Count)102
- Executing Action-On-Trigger or GO/NO-GO Determination (Exec)103
- GO/NO-GO Determination (Go/Nogo AND, Go/Nogo OR)103
- Notes about Action107
6 Waveform Acquisition108
- Record Length (Record Length)108
- Acquisition Mode (Mode)109
- High Resolution Mode (Hi Resolution)110
- Sampling Mode (Sampling Mode)111
- Waveform Acquisition (RUN/STOP)112
- Acquiring the Waveform Once (SINGLE)112
7 Display113
- Types of Windows113
- Display Format (Format)113
- Display Interpolation (Dot Connect)114
- Graticule (Graticule)115
- Scale Value Display (Scale Value)115
- Waveform Intensity (Intensity)115
- Accumulation (Accumulate)116
8 Displaying XY Waveforms117
- Turning the XY Waveform Display on and off (Display)117
- X-Axis and Y-Axis Source Waveforms (X Trace/Y Trace)117
- Configuring the Display (Display Setup)117
- Display Source Window (Time Range)118
- Display Area (T Range1/T Range2)118
- Measurement (Measure Setup)118
9 Computed and Reference Waveforms119
- Computation Mode (Mode)119
- Computation Source Waveforms (Source1/Source2)119
- Reference Waveforms120
- Operators (Operation)121
- Initial Point (Initial Point)124
- Setting Labels and Units (Label/Unit)124
- Scaling (Ranging)125
- User-Defined Computation (User Define, Option)125
10 Fft132
- Turning the FFT on or off (Display)132
- Analysis Source Waveform (Trace)132
- FFT Conditions (FFT Setup)133
- Number of FFT Points (FFT Point)134
- Analysis Range (Time Range)134
- Scale Value (Display Setup)135
- Cursor Measurement (Measure Setup)135
11 Cursor Measurement137
- Turning Cursor Measurement on and off (Display)137
- Cursor Mode (Type)137
- Measurement Source Waveform (Trace)137
- ΔT Cursors (ΔT)138
- ΔV Cursors (ΔV)138
- ΔT&ΔV Cursors (ΔT&ΔV)139
- Marker Cursors (Marker)139
- Angle Cursors (Degree)140
- Moving the Cursors (Cursor/Marker)140
- Cursor Jumping (Cursor Jump/T Cursor Jump)141
12 Automated Measurement of Waveform Parameters142
- Turning Automated Measurement on or off (Mode)142
- Source Window (Time Range)142
- Measurement Time Period (T Range1/T Range2)142
- Statistics (Statistics)148
- Enhanced Parameter Measurement (Enhanced)153
- Notes about Automated Measurement of Waveform Parameters154
13 Zooming in on Waveforms155
- Turning the Zoom Windows on or off (Display)155
- Display Format (Format)155
- Displaying the Main Window (Main)156
- Auto Scrolling (Auto Scroll)156
- Zoom Source Waveforms (Trace)156
- Zoom Factor (ZOOM Knob)156
- Zoom Position (Z1 Position, Z2 Position)157
- Vertical Zoom (Vertical Zoom)157
14 Searching Waveforms158
- Search Source Waveform158
- Search Type (Type)158
- Search Conditions (Condition Setup)161
- Displaying Detected Waveforms (Display Setup)164
- Search Skip (Skip Mode)164
- Search Range (Start/End Point)165
- Detected Point Number (Pattern No.)165
- Executing a Search (Search)165
15 Analyzing and Searching Serial Bus Signals166
- Turning the Analysis and Search Feature on or off (Display)166
- Serial Bus Signal Type (Type)167
- Bus Setup (Setup)167
- Search Setup (Search)167
- Zoom Position (Z1 Position, Z2 Position)168
- Decoded Display (Decode)168
- List Display (List)169
- Trend Display (Trend)169
- Saving the Analysis Results169
- Analyzing and Searching Flexray Bus Signals (Option)170
- Analyzing and Searching CAN Bus Signals (Option)172
- Analyzing and Searching CAN FD Bus Signals (Option)174
- Analyzing and Searching LIN Bus Signals (Option)179
- Analyzing and Searching CXPI Bus Signals (Option)182
- Analyzing and Searching SENT Signals (Option)188
- Analyzing and Searching UART Signals (Option)193
- C Bus Signals (Option)196
- Analyzing and Searching SPI Bus Signals (Option)198
- Analyzing and Searching User-Defined Serial Bus Signals (User Define)200
16 Waveform Histogram Display201
- Turning the Histograms on or off (Display)201
- Source Waveform (Trace)201
- Source Axis (Type)201
- Range Setup (Range Setup)201
- Measurement (Measure Setup)202
17 Power Supply Analysis Feature (Power Analysis and Power Measurement, Option)203
- Overview of the Power Supply Analysis Feature203
- Switching Loss Analysis (SW Loss)204
- Safe Operating Area Analysis (SOA)209
- Harmonic Analysis (Harmonics)210
- Measuring Inrush Current by Computing the Joule Integral (I 2 T)214
- Power Measurement (Power Measurement)216
18 Displaying and Searching History Waveforms220
- Display Mode (Mode)221
- Average (Average)221
- Highlighting (Select No.)221
- Display Range (Start/End No.)221
- List of Timestamps (List)221
- Searching History Waveforms (Search)222
- Replay (Replay)223
- Notes on Using the History Feature223
19 Printing and Saving Screen Captures224
- Destination Type (Print To)224
- Printing on the Built-In Printer (Builtin) (Option)225
- Printing on a USB Printer (USB)225
- Printing on a Network Printer (Network)227
- Saving Screen Captures to Files (File)228
- Printing and Saving Screen Captures to Multiple Destinations (Multi)230
20 Saving and Loading Data231
- Storage Device You Can Save and Load from231
- Saving Data (Save)232
- Saving Waveform Data (Waveform)232
- Saving Setup Data (Setup)235
- Saving Other Types of Data (Others)235
- Serial Bus Analysis Results (Others - Serial Bus (Flexray/Can/Can FD/LIN/CXPI))238
- Serial Bus Analysis Results238
- C/Spi))241
- Loading Data (Load)244
- File Operations (Utility)246
21 Ethernet Communication (Network)248
- Tcp/Ip(Tcp/Ip)249
- FTP Server (FTP Server)250
- Mail (Mail)251
- Network Drive (Net Drive)252
- Network Printer (Net Print)253
- Sntp (Sntp)253
22 Other Features254
- Auto Setup (AUTO SETUP)254
- Default Settings (DEFAULT SETUP)255
- Snapshot (SNAP SHOT)255
- Clear Trace (CLEAR TRACE)256
- Calibration (Calibration)256
- Remote Control (Remote Control)257
- System Configuration (System Configuration)259
- Overview (Overview)262
- Self-Test (Self Test)263
- Touch Panel (TOUCH)263
Appendix264
- Appendix 2 User-Defined Computation266
  - FFT Function270
- Appendix 3 ASCII Data File Format273
- Appendix 4 TCP and UDP Port Numbers274
- Appendix 5 How Power Measurement Items Are Determined275
- Appendix 6 Trigger and Detected Points of SENT Signals276
- Appendix 7 Firmware Version and New Features277
Index278

Brand	YOKOGAWA
Model	DLM3054
Category	Test Equipment
Language	English

YOKOGAWA DLM3054 User Manual

Table of Contents

Questions and Answers:

YOKOGAWA DLM3054 Specifications

Related product manuals