Why is the compressor over-running on my Zip Water Filtration Systems?
If your Zip Water Filtration System's compressor is over-running, this could be because the compressor is too hot. Ensure that the unit has adequate ventilation.
How to fix a blocked condenser screen on a Zip Water Filtration Systems?
If the condenser screen of your Zip Water Filtration System is blocked, it's likely due to a blocked air filter. Remove the blockage, clean the filter, and check the user guide for further assistance.
What to do if my Zip Water Filtration Systems shows condenser overtemp.?
If the condenser on your Zip Water Filtration System is overheating, it's likely due to a blocked air filter. Remove any blockage and clean the filter. You may also consult the user guide for detailed instructions.
What to do if my Zip Water System has no water supply?
If your Zip Water System isn't getting water, the first thing to do is check that the water supply is turned ON.
What causes condenser overtemp in Zip HydroTap G4 Water System?
If the condenser of your Zip Water System is experiencing overtemperature, this is likely due to a blocked air filter. Remove any blockage and clean the filter. Refer to the user guide for detailed instructions.
What does 'Calibration' mean on my Zip HydroTap G4?
If your Zip Water System displays 'Calibration', this indicates a normal auto calibration reset, which occurs approximately once per month.
Why does calibration happen on my Zip Water Filtration Systems?
Calibration in your Zip Water Filtration System that occurs once per month is a normal operation due to auto calibration reset.
What to do if there is a water leak in my Zip Water Filtration System?
If your Zip Water Filtration System experiences a water leak, immediately turn off the mains water supply and call for service.
What to do if the water supply failed on my Zip Water Filtration Systems?
If your Zip Water Filtration System is experiencing a water supply failure, it's likely due to the water supply not being turned ON. Ensure that the water supply is turned ON.
What to do if the boil dry protection is activated in Zip Water Filtration Systems?
If your Zip Water Filtration System's boil dry protection has activated, it's likely due to the safety mechanism being triggered. To reset, turn the power OFF and then ON again.
Instructions for configuring the tap's safety feature via the menu.
Steps to enable the safety lock directly from the tap.
Steps to disable the safety lock directly from the tap.
Explains touch-sensitive controls for dispensing water types.
Details operation of the two levers for dispensing water.
Instructions for dispensing chilled water on different HydroTap models.
Steps for dispensing boiling water when safety is off.
Steps for dispensing boiling water with safety lock engaged.
Indicates boiling water status (ready or below temperature).
Flashing light indicates a system fault requiring attention.
Shows filter status (off, flashing for replacement).
Step 1 for safety sensor calibration procedure.
Step 7 for checking calibration after adjustment.
Lists status messages like Safety OFF, System Fault, Sleep Mode.
Lists main menu categories: Language, Information, Installation, Service, Security, Communication, Settings.
Details for Date/Time, Temperature, Filter, Energy Modes, Safety, Dispense Time settings.
Instructions for flushing the filter system after installation or replacement.
Instructions to reset filter counters after replacing the filter.
Procedure and caution for calibrating boiling water temperature.
Section reserved for service technicians only; contact details provided.
Allows setting up a password to protect system settings.
Steps to set a 4-digit password for system settings access.
Functionality for using Wi-Fi to monitor and control the product remotely.
Accesses system settings like password, date/time, temperature.
Details on operating temperatures for boiling and chilled water.
Allows changing the maximum dispensing time for water.
Notifies when filter replacement is due and lists indicators.
Steps for opening unit, relieving pressure, and replacing cartridge.
Location, inspection, cleaning, and replacement of the air filter.
Step 1 of the CO2 bottle change procedure.
Step 11 of the CO2 bottle change procedure.
Step 15 of the CO2 bottle change procedure.
Recommended cleaning instructions using soft cloth and mild soap.
Icon indicating the safety switch is locked, preventing Boiling water dispense.
Displays the set temperature for boiling water.
Provides Zip Heaters (Aust) Pty Ltd contact information.
Telephone number for customer support and inquiries.
General| Model | HydroTap G4 |
|---|---|
| Category | Water System |
| Power Supply | 220-240V, 50Hz |
| Dimensions | Varies by model |
| Weight | Varies by model |
| Boiling Water Capacity | Up to 160 cups per hour |
| Filter | Advanced filtration system |
| Safety | Child safety lock |
| Filtration | 0.2 micron |
| Energy Efficiency | Energy-saving mode |
| Warranty | 5 years |
| Chilled Water Capacity | Varies by model (e.g., up to 175 cups/hour) |
To Next Page
