How to reset boil dry protection on a Zip Water System?
If the boil dry protection has been activated on your Zip Water System, the safety mechanism has been triggered. Turn the power OFF and then ON to reset it.
What to do if my Zip Water Dispenser is leaking water?
If your Zip Water Dispenser is leaking water, immediately turn off the mains water supply and call for service.
Why is there no water coming from my Zip Water Dispenser?
If there's no water coming from your Zip Water Dispenser, the first thing to check is whether the water supply is turned ON.
How to reset boil dry protection on Zip Water Dispenser?
To reset the boil dry protection on your Zip Water Dispenser, turn the power OFF and then ON.
What to do if my Zip Water Dispenser condenser is overheating?
If your Zip Water Dispenser's condenser is overheating, the air filter might be blocked. Remove the blockage, clean the filter, and check the user guide for further instructions.
What to do if the condenser screen of Zip Water Dispenser is blocked?
If the condenser screen of your Zip Water Dispenser is blocked, remove the blockage, clean the filter, and check the user guide.
What to do if my Zip Water Dispenser compressor is over-running?
If the compressor in your Zip Water Dispenser is over-running, check the ventilation to ensure it's adequate.
What does 'Power board fault' mean on a Zip Water Dispenser?
A 'Power board fault' on your Zip Water Dispenser indicates an electrical disruption. Check the power supply and all fuses.
Why is the condenser overheating in my Zip Water Filtration System?
If the condenser of your Zip Water Filtration System is overheating, it's likely due to a blocked air filter. Remove any blockage, clean the filter, and consult the user guide for further instructions.
Why does the compressor in my Zip Water Filtration System over run?
If the compressor in your Zip Water Filtration System is running excessively, ensure that the ventilation is adequate.
Instructions for configuring the tap's safety feature via the menu.
Steps to enable the safety lock directly from the tap.
Steps to disable the safety lock directly from the tap.
Explains touch-sensitive controls for dispensing water types.
Details operation of the two levers for dispensing water.
Instructions for dispensing chilled water on different HydroTap models.
Steps for dispensing boiling water when safety is off.
Steps for dispensing boiling water with safety lock engaged.
Indicates boiling water status (ready or below temperature).
Flashing light indicates a system fault requiring attention.
Shows filter status (off, flashing for replacement).
Step 1 for safety sensor calibration procedure.
Step 7 for checking calibration after adjustment.
Lists status messages like Safety OFF, System Fault, Sleep Mode.
Lists main menu categories: Language, Information, Installation, Service, Security, Communication, Settings.
Details for Date/Time, Temperature, Filter, Energy Modes, Safety, Dispense Time settings.
Instructions for flushing the filter system after installation or replacement.
Instructions to reset filter counters after replacing the filter.
Procedure and caution for calibrating boiling water temperature.
Section reserved for service technicians only; contact details provided.
Allows setting up a password to protect system settings.
Steps to set a 4-digit password for system settings access.
Functionality for using Wi-Fi to monitor and control the product remotely.
Accesses system settings like password, date/time, temperature.
Details on operating temperatures for boiling and chilled water.
Allows changing the maximum dispensing time for water.
Notifies when filter replacement is due and lists indicators.
Steps for opening unit, relieving pressure, and replacing cartridge.
Location, inspection, cleaning, and replacement of the air filter.
Step 1 of the CO2 bottle change procedure.
Step 11 of the CO2 bottle change procedure.
Step 15 of the CO2 bottle change procedure.
Recommended cleaning instructions using soft cloth and mild soap.
Icon indicating the safety switch is locked, preventing Boiling water dispense.
Displays the set temperature for boiling water.
Provides Zip Heaters (Aust) Pty Ltd contact information.
Telephone number for customer support and inquiries.
General| Model | HydroTap G4 |
|---|---|
| Category | Water System |
| Power Supply | 220-240V, 50Hz |
| Dimensions | Varies by model |
| Weight | Varies by model |
| Boiling Water Capacity | Up to 160 cups per hour |
| Filter | Advanced filtration system |
| Safety | Child safety lock |
| Filtration | 0.2 micron |
| Energy Efficiency | Energy-saving mode |
| Warranty | 5 years |
| Chilled Water Capacity | Varies by model (e.g., up to 175 cups/hour) |
To Next Page