Why is my Zip Water System condenser overheating?
If your Zip Water System is experiencing condenser overtemp, the cause may be a blocked air filter. Remove any blockage, clean the filter, and consult the user guide.
Why is the compressor over-running on my Zip HydroTap G4 Water System?
If the compressor is over-running on your Zip Water System, it might be too hot. Check the ventilation to ensure it's adequate.
How to troubleshoot a power board fault in Zip Water Filtration Systems?
If your Zip Water Filtration System displays a power board fault, the issue might stem from an electrical disruption. To address this, check the power supply and all fuses connected to the system.
What to do if the boil dry protection is activated in Zip Water Filtration Systems?
If your Zip Water Filtration System's boil dry protection has activated, it's likely due to the safety mechanism being triggered. To reset, turn the power OFF and then ON again.
What to do if the water supply failed on my Zip Water Filtration Systems?
If your Zip Water Filtration System is experiencing a water supply failure, it's likely due to the water supply not being turned ON. Ensure that the water supply is turned ON.
What to do if there is a water leak in my Zip Water Filtration System?
If your Zip Water Filtration System experiences a water leak, immediately turn off the mains water supply and call for service.
What to do if my Zip Water Filtration System has a water supply failure?
If you are experiencing a Water Supply Failure with your Zip Water Filtration System, the first thing you should do is check that the water supply is turned ON.
What to do if the boil dry protection is activated on my Zip Water Filtration System?
If your Zip Water Filtration System has tripped the boil dry protection, which was activated for safety reasons, turn the power OFF and then ON to reset the system.
What to do if there is a water leak in my Zip Water Filtration Systems?
If you notice a water leak in your Zip Water Filtration System, immediately turn off the mains water supply to prevent further leakage and then call for service.
Why is there a water supply failure in my Zip Water Filtration Systems?
If your Zip Water Filtration System isn't dispensing water, the first thing to check is whether the water supply is turned ON. Ensure that the water supply is properly connected and activated.
Instructions for configuring the tap's safety feature via the menu.
Steps to enable the safety lock directly from the tap.
Steps to disable the safety lock directly from the tap.
Explains touch-sensitive controls for dispensing water types.
Details operation of the two levers for dispensing water.
Instructions for dispensing chilled water on different HydroTap models.
Steps for dispensing boiling water when safety is off.
Steps for dispensing boiling water with safety lock engaged.
Indicates boiling water status (ready or below temperature).
Flashing light indicates a system fault requiring attention.
Shows filter status (off, flashing for replacement).
Step 1 for safety sensor calibration procedure.
Step 7 for checking calibration after adjustment.
Lists status messages like Safety OFF, System Fault, Sleep Mode.
Lists main menu categories: Language, Information, Installation, Service, Security, Communication, Settings.
Details for Date/Time, Temperature, Filter, Energy Modes, Safety, Dispense Time settings.
Instructions for flushing the filter system after installation or replacement.
Instructions to reset filter counters after replacing the filter.
Procedure and caution for calibrating boiling water temperature.
Section reserved for service technicians only; contact details provided.
Allows setting up a password to protect system settings.
Steps to set a 4-digit password for system settings access.
Functionality for using Wi-Fi to monitor and control the product remotely.
Accesses system settings like password, date/time, temperature.
Details on operating temperatures for boiling and chilled water.
Allows changing the maximum dispensing time for water.
Notifies when filter replacement is due and lists indicators.
Steps for opening unit, relieving pressure, and replacing cartridge.
Location, inspection, cleaning, and replacement of the air filter.
Step 1 of the CO2 bottle change procedure.
Step 11 of the CO2 bottle change procedure.
Step 15 of the CO2 bottle change procedure.
Recommended cleaning instructions using soft cloth and mild soap.
Icon indicating the safety switch is locked, preventing Boiling water dispense.
Displays the set temperature for boiling water.
Provides Zip Heaters (Aust) Pty Ltd contact information.
Telephone number for customer support and inquiries.
General| Model | HydroTap G4 |
|---|---|
| Category | Water System |
| Power Supply | 220-240V, 50Hz |
| Dimensions | Varies by model |
| Weight | Varies by model |
| Boiling Water Capacity | Up to 160 cups per hour |
| Filter | Advanced filtration system |
| Safety | Child safety lock |
| Filtration | 0.2 micron |
| Energy Efficiency | Energy-saving mode |
| Warranty | 5 years |
| Chilled Water Capacity | Varies by model (e.g., up to 175 cups/hour) |
To Next Page
