ABB A135-M55 - Page 144

Operation Manual / 4 Product description / A130-M.. - A145-M..
Tables
© Copyright 2020 ABB. All rights reserved. HZTL4031_EN Revision L July 2020
Tables
Table1: Related documents .......................................... 3
Table2: Weight of complete turbocharger unit....... 8
Table3: Requirements for threaded rods ................ 15
Table4: Tightening torque for standard nuts......... 17
Table5: Torque-controlled tightening of the pres-
sure screws .................................................................... 19
Table6: Lubricating oil pressure at oil inlet before
turbocharger .................................................................. 27
Table7: Lubricating oil temperature at the inlet ... 28
Table8: Lubricating oil temperature at the outlet 28
Table9: Tightening torque(86505)........................... 32
Table10: Expected replacement intervals .............. 39
Table11: Maintenance table ....................................... 42
Table12: Parameters for wet cleaning of com-
pressor ........................................................................... 45
Table13: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 48
Table14: Wet cleaning of turbine, parameters ...... 49
Table15: Value table for soaking ............................... 57
Table16: Malfunctions when starting – Delayed
start-up .......................................................................... 60
Table17: Malfunctions when starting – Vibrations 60
Table18: Malfunctions when starting – Rubbing of
rotating parts................................................................ 60
Table19: Malfunctions during operation – Lubricat-
ing oil pressure too low................................................ 61
Table20: Malfunctions during operation – Speed re-
duces................................................................................ 61
Table21: Malfunctions during operation – Speed in-
creases ............................................................................ 61
Table22: Malfunctions during operation – Exhaust
gas temperature too high .......................................... 62
Table23: Malfunctions during operation – Charge air
pressure too low........................................................... 62
Table24: Malfunctions during operation – Charge air
pressure too high ......................................................... 63
Table25: Malfunctions during operation – Engine
performance losses ..................................................... 63
Table26: Malfunction – Turbocharger pumping.... 64
Table27: Malfunction – Sporadic surge blows ........ 64
Table28: Malfunctions when stopping – Runout
noises............................................................................... 65
Table29: Malfunctions when stopping – Runout
time too short ................................................................ 65
Table30: Malfunction of the speed measurement
system – No signal or poor signal amplitude .......... 66
Table31: Malfunction of the speed measurement
system – Measured speed too high ........................... 66
Table32: Malfunction of the speed measurement
system – Measured speed too low............................. 66
Table33: Swivel lifting eyes......................................... 68
Table34: Weights of assemblies................................ 70
Table35: 3 press-off screws........................................ 74
Table36: 6 press-off screws........................................ 75
Table37: Permissible clearances A and B ................. 83
Table38: Nozzle ring compression PD ...................... 84
Table39: Tightening torque (51007) ......................... 87
Table40: Tightening torque (79041) ......................... 89
Table41: Tightening torque (72011) .......................... 90
Table42: Permissible clearances N and R................. 91
Table43: Tightening torque (72020) ......................... 92
Table44: Tightening torque (51009)......................... 95
Table45: Tightening torques...................................... 97
Table46: Tightening torques for insulation ............ 98
Table47: Cover plate dimensions [mm].................. 102
Table48: Customer spare part set 97070 .............. 106
Table49: Spare parts list ........................................... 109
Table50: Spare parts list ........................................... 110
Table51: Customer tool set 90000........................... 111
Page 114 / 114Page 114 / 114