ABB HT611036 Instruction Manual

Operation Manual / 4 Product description / A150-M56/66/57/67 -
A155-M..
Tables
© Copyright 2020 ABB. All rights reserved. HZTL4032_EN Revision P March 2020
Tables
Table1: Related documents .......................................... 5
Table2: Weight of complete turbocharger unit...... 10
Table3: Fitting the turbocharger, value X, L............ 16
Table4: Torque-controlled tightening of the pres-
sure screws .................................................................... 18
Table5: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 25
Table6: Lubricating oil temperature at the inlet... 26
Table7: Maximum lubricating oil temperature at the
outlet .............................................................................. 26
Table8: Tightening torque(86505).......................... 30
Table9: Expected replacement intervals ................ 36
Table10: Maintenance table ...................................... 39
Table11: Parameters for wet cleaning of compressor
42
Table12: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 45
Table13: Wet cleaning of turbines, parameters for 1-
nozzle cleaning.............................................................. 46
Table14: Wet cleaning of turbines, parameters for 6-
nozzle cleaning.............................................................. 47
Table15: Value table for soaking .............................. 54
Table16: Tightening torque (81152 / 81154)........... 58
Table17: Malfunctions when starting – Delayed
start-up .......................................................................... 59
Table18: Malfunctions when starting – Vibrations 59
Table19: Malfunctions when starting – Rubbing of
rotating parts................................................................ 59
Table20: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 60
Table21: Malfunctions during operation – Speed re-
duces............................................................................... 60
Table22: Malfunctions during operation – Speed in-
creases ........................................................................... 60
Table23: Malfunctions during operation – Exhaust
gas temperature too high ........................................... 61
Table24: Malfunctions during operation – Charge air
pressure too low............................................................ 61
Table25: Malfunctions during operation – Charge air
pressure too high ......................................................... 62
Table26: Malfunctions during operation – Engine
performance losses....................................................... 62
Table27: Malfunction – Turbocharger pumping ..... 63
Table28: Malfunction – Sporadic surge blows ........ 63
Table29: Malfunctions when stopping – Runout
noises............................................................................... 64
Table30: Malfunctions when stopping – Runout
time too short ................................................................ 64
Table31: Malfunction of the speed measurement
system – No signal or poor signal amplitude .......... 65
Table32: Malfunction of the speed measurement
system – Measured speed too high ........................... 65
Table33: Malfunction of the speed measurement
system – Measured speed too low............................. 65
Table34: Swivel lifting eyes......................................... 67
Table35: Press-off screws........................................... 68
Table36: Dismantling screw ....................................... 68
Table37: Weights of assemblies ................................ 73
Table38: Tightening torques ...................................... 75
Table39: Tightening torques for insulation ............ 76
Table40: 3 press-off screws ....................................... 83
Table41: 6 press-off screws........................................ 84
Table42: Tightening torque (90012-01).................... 89
Table43: Permissible clearances A and B ................. 94
Table44: Nozzle ring compression PD...................... 95
Table45: Tightening torque (90012-01) ................... 98
Table46: Tightening torque (51007) ......................... 99
Table47: Tightening torque (79041) ....................... 100
Table48: Tightening torque (72011) ....................... 101
Table49: Permissible clearances N and R............... 104
Table50: Tightening torque (51009)....................... 107
Table51: Tightening torque (51009)........................ 108
Table52: Tightening torque (72051)........................ 110
Table53: Tightening torque (72054) ........................ 111
Table54: Threaded rod, value X................................. 118
Table55: Permissible clearances A and B ............... 122
Page 170 / 171Page 170 / 171

ABB HT611036 Specifications

General

Brand	ABB
Model	HT611036
Category	Industrial Equipment
Language	English