Adcom GFR-700HD - Page 54

54
Chapter 3 - Setup
GFR-700HD Owner’s Manual
Function Description Data ASCII
Subwoofer Channel Trim - 0x4C
L
Lip Sync Adjust Down (Decrease
delay)
0x0D CR
Lip Sync Adjust Up (Increase delay) 0x60
`
Theater EQ compensation - ON 0x69
i
Theater EQ compensation - OFF 0x6A
j
Select: “tape” Monitor (Toggle
On/Off)
0x71
q
Select: “ext 7.1 inputs” - On 0x26
&
Select: “ext 7.1 inputs” - Off 0x2A
*
Select Analog “audio” input (for
Current Source)
0x59
Y
Select Digital “coaxial 1” input (for
Current Source)
0x5A
Z
Select Digital “coaxial 2” input (for
Current Source)
0x3A
:
Select Digital “coaxial 3” input (for
Current Source)
0x3B
;
Select Digital “optical 1” input (for
Current Source)
0x05 ENQ
Select Digital “optical 2” input (for
Current Source)
0x24
$
Select Digital “optical 3” input (for
Current Source)
0x27
’
Select Source: VIDEO 1 0x6B
k
Select Source: VIDEO 2 0x6C
l
Select Source: VIDEO 3 0x6D
m
Select Source: VIDEO 4 0x6E
n
Select Source: CD 0x70
p
Select Source: TUNER (AM) 0x6F
o
Select Source: TUNER (FM) 0x72
r
TUNER Scan + 0x61
a
TUNER Scan - 0x62
b
TUNER STEP + 0x63
c
TUNER STEP - 0x64
d
FM mode – MONO 0x65
e
FM mode – STEREO 0x66
f
Function Description Data ASCII
TUNER mode – PRESET 0x67
e
TUNER mode – TUNE 0x68
h
TUNER MEMORY Function (Select/
Save)
0x73
s
TUNER Preset 1 Select 0x74
t
TUNER Preset 2 Select 0x75
u
TUNER Preset 3 Select 0x76
v
TUNER Preset 4 Select 0x77
w
TUNER Preset 5 Select 0x78
x
TUNER Preset 6 Select 0x79
y
TUNER Preset 7 Select 0x7A
z
TUNER Preset 8 Select 0x7C
|
TUNER Preset 9 Select 0x7E
~
TUNER Preset 10+ Select (access
11-32)
0x7F
Tone EQ Control - On 0x0C FF
Tone EQ Control - Off 0x13 DC3
Tone EQ Control – Toggle On/Off 0x15 NAK
Tone Reset (Set Bass & Treble =
0dB)
0x14 DC4
Bass EQ Adjust 0x16 SYN
Treble EQ Adjust 0x17 ETB
Room 2 Volume UP (when RM2 is
active)
0x01 SQH
Room 2 Volume DOWN (when RM2
is active)
0x02 STX
Room 2 Mute (when RM2 is active) 0x03 ETX
Room 2 Un-mute (when room 2 is
active)
0x04 EOT
Selects Input: VID 2 for Room 2
(when RM2 is active)
0x06 ACK
Selects Input: VID 3 for Room 2
(when RM2 is active)
0x07 BELL
Selects Input: VID 4 for Room 2
(when RM2 is active)
0x08 BS
Selects Input: CD for Room 2 (when
RM2 is active)
0x09 HT
Selects TUNER for Room 2 (when
RM2 is active)
0x0B VT