Need help?Do you have a question about the ADJ DMX Operator and is the answer not in the manual?
Information on how to contact ADJ for setup help, questions, and suggestions.
Used to select individual fixtures for programming or control, determining DMX channel assignment.
Used for storing scenes in program mode or playing back scenes in playback mode.
Shows values and settings based on the controller's current function.
Used to navigate and select between the 30 available banks of scenes.
Used to select and control the 6 available chases.
Activates the programming mode, indicated by a blinking display.
Controls MIDI operations and records steps for scenes and chases.
Selects auto speed in chase mode or deletes scenes and chases.
Triggers sound activation or copies scene banks between different locations.
Disables or enables all channel outputs for immediate darkness.
Adjusts chase rate in auto mode or changes LCD display in manual chase.
Controls the duration for scene transitions, from instant to 30 seconds.
Adjusts the playback speed for chases in automatic mode.
Switches between page A (1-8) and page B (9-16) channel banks.
Used to manually adjust DMX channel values from 0% to 100%.
Receives MIDI data from external devices for control.
Sends DMX signals to lighting fixtures or DMX interfaces.
Supports connecting LED lamps, backing up settings, and updating controller firmware.
Connection point for the external power supply.
Function to duplicate the settings of one scene to another scene.
Process for modifying existing programmed scenes by adjusting fader values.
Procedure to clear all recorded scenes from all banks, resetting the controller.
Copies all scenes from one bank to another bank.
Removes all scenes from a selected bank.
Resets all DMX channels for a single scene back to zero.
Steps to record chases, which are sequences of scenes, for automated lighting shows.
Instructions on how to insert a new step into an existing chase sequence.
Removes a specific step from a chase sequence.
Erases an entire recorded chase from the controller's memory.
Clears all recorded chases from the controller.
Executes programmed scenes manually, stepping through them one by one.
Steps through a chase sequence manually, allowing control over each step.
Plays back programmed scenes automatically in a sequential loop with adjustable speed and fade.
Runs chases automatically, allowing adjustment of speed and fade times.
Plays back scenes in sync with external audio input.
Plays back chases in sync with external audio input.
Fine-tunes the controller's response to audio cues for sound-activated modes.
Process for saving controller settings, scenes, and chases to a USB drive.
Restores controller settings from a USB drive back to the unit.
Guide to updating the DMX Operator's firmware using a USB drive.
Information on how to contact ADJ for setup help, questions, and suggestions.
Used to select individual fixtures for programming or control, determining DMX channel assignment.
Used for storing scenes in program mode or playing back scenes in playback mode.
Shows values and settings based on the controller's current function.
Used to navigate and select between the 30 available banks of scenes.
Used to select and control the 6 available chases.
Activates the programming mode, indicated by a blinking display.
Controls MIDI operations and records steps for scenes and chases.
Selects auto speed in chase mode or deletes scenes and chases.
Triggers sound activation or copies scene banks between different locations.
Disables or enables all channel outputs for immediate darkness.
Adjusts chase rate in auto mode or changes LCD display in manual chase.
Controls the duration for scene transitions, from instant to 30 seconds.
Adjusts the playback speed for chases in automatic mode.
Switches between page A (1-8) and page B (9-16) channel banks.
Used to manually adjust DMX channel values from 0% to 100%.
Receives MIDI data from external devices for control.
Sends DMX signals to lighting fixtures or DMX interfaces.
Supports connecting LED lamps, backing up settings, and updating controller firmware.
Connection point for the external power supply.
Function to duplicate the settings of one scene to another scene.
Process for modifying existing programmed scenes by adjusting fader values.
Procedure to clear all recorded scenes from all banks, resetting the controller.
Copies all scenes from one bank to another bank.
Removes all scenes from a selected bank.
Resets all DMX channels for a single scene back to zero.
Steps to record chases, which are sequences of scenes, for automated lighting shows.
Instructions on how to insert a new step into an existing chase sequence.
Removes a specific step from a chase sequence.
Erases an entire recorded chase from the controller's memory.
Clears all recorded chases from the controller.
Executes programmed scenes manually, stepping through them one by one.
Steps through a chase sequence manually, allowing control over each step.
Plays back programmed scenes automatically in a sequential loop with adjustable speed and fade.
Runs chases automatically, allowing adjustment of speed and fade times.
Plays back scenes in sync with external audio input.
Plays back chases in sync with external audio input.
Fine-tunes the controller's response to audio cues for sound-activated modes.
Process for saving controller settings, scenes, and chases to a USB drive.
Restores controller settings from a USB drive back to the unit.
Guide to updating the DMX Operator's firmware using a USB drive.
General| Brand | ADJ |
|---|---|
| Model | DMX Operator |
| Category | Recording Equipment |
| Language | English |
To Next Page
