Adleepower MS2-107 - User Manual

Questions and Answers

R
Richard HuberAug 6, 2025
What to do if my Adleepower Inverter shows PF01?
- C
  Crystal BairdAug 6, 2025
  If your Adleepower Inverter displays the error code PF01, it could be due to several reasons. It may be caused by power device failure during acceleration, in which case you should increase the acceleration time. Alternatively, the boost voltage might be too high, so you should reduce CD21 contents. Another possible cause is a locked motor or an excessively heavy load; try reducing the load factor. Finally, check for disconnected output wiring (W.V.U.) and repair if necessary.
D
dsmithAug 10, 2025
What to do if my Adleepower Inverter shows PF02?
- D
  Dustin JonesAug 10, 2025
  If your Adleepower Inverter displays the error code PF02, it might be due to a power device failure during constant frequency operation. Try to eliminate any sudden changes in load. Another possible reason is that the ambient temperature is too high, and you should attempt to reduce it.
A
Andrew SmithAug 14, 2025
What to do if my Adleepower MS2-107 Inverter shows PF03?
- S
  Shannon McclainAug 14, 2025
  If your Adleepower Inverter displays the error code PF03, it could be due to a power device failure during deceleration. To resolve this, increase the deceleration time. It could also be caused by over voltage, in which case you should connect a braking resistor.
J
Joshua PhillipsAug 18, 2025
What to do if my Adleepower MS2-107 Inverter shows PF04?
- G
  Gina RamosAug 19, 2025
  If your Adleepower Inverter displays the error code PF04, it may be caused by a power device failure during stand-by. Remove the cause of the failure. Another possible reason is that the power supply voltage is too high, so reduce the voltage.
G
George LevyAug 23, 2025
What to do if my Adleepower MS2-107 Inverter shows EEP1?
- A
  Alison DoughertyAug 23, 2025
  If your Adleepower Inverter displays the error code EEP1, it indicates a communication reset error. Refer to address 100 description. If the same message appears again, rework with the previous process, or repair.
A
Amanda ThompsonAug 27, 2025
What to do if my Adleepower Inverter shows EEP2?
- T
  Tammy GonzalezAug 27, 2025
  If your Adleepower Inverter displays the error code EEP2, it indicates an EEPROM check-sum error. Rework with the previous process, and if the same message appears again, repair.
A
Allen WhitakerAug 31, 2025
How to fix no display on Adleepower MS2-107?
- B
  Brandon OrtizAug 31, 2025
  If the display on your Adleepower Inverter is not working, it might be because the discharge LED is extinguished. Ensure it is turned on, or replace the MCCB.

Summary

Preface and Safety Guidelines

General Precautions

General safety guidelines and precautions for using the inverter.

Safety Symbols and Warnings

Explanation of safety symbols (Warning, Caution) used in the manual.

Receiving and Installation Safety

Safety notes for receiving the product and initial installation steps.

Operation and Maintenance Safety

Crucial safety guidelines for operating and maintaining the inverter.

Installation and Terminal Details

Installation Requirements

Terminal Descriptions

Identification and connection diagrams for main and control circuit terminals.

Wiring and System Connection

Main Circuit Wiring

Control Signal and Grounding

Operation and Functions

Function Setting Procedures

Communication Protocol and Error Handling

Troubleshooting and Applications

Display Error Codes

List and explanation of inverter error codes and their causes.

Precautions

Important precautions before maintenance and during application use.

Troubleshooting Guide

Common fault messages, check points, and suggested remedies for inverter issues.

Adleepower MS2-107 Specifications

General

Model	MS2-107
Category	Inverter
Input Voltage	12V DC
Output Voltage	110V AC
Frequency	60Hz
Efficiency	90%
Cooling	Fan
USB Ports	2
Protection	Overload, Overheat, Short Circuit