AL-KO Robolinho 1150 User Manual (English)

Other manuals for AL-KO Robolinho 1150

Manual652 pages

Translation Of The Original Instructions For Use484 pages

Questions and Answers:

H
howardpierceAug 31, 2025
Why does my AL-KO Lawn Mower show Cal: signal weak?
- J
  Jennifer FerrellAug 31, 2025
  If your AL-KO Lawn Mower displays 'Cal: signal weak' during calibration, place the appliance at the prescribed calibrating position, aligned precisely at right angles. Also, check the power source of the base station by disconnecting and reconnecting it, and inspect the boundary cable for damage. This can happen because the loop signal is too weak or there is no loop signal, or the boundary cable is faulty.
R
ryan20Aug 30, 2025
What to do if AL-KO Robolinho 1150 Lawn Mower shows Cal: no loop CN015: Cal: outside?
- C
  Carolyn CombsAug 30, 2025
  If your AL-KO Lawn Mower displays 'Cal: no loop' or 'CN015: Cal: outside' during calibration, check the LEDs on the base station and the power source by disconnecting and reconnecting it. Place the appliance at the prescribed calibrating position, aligned precisely at right angles, ensuring it can drive over the boundary cable. This issue arises because the appliance cannot find the boundary cable during calibration.
T
timothy21Aug 28, 2025
How to fix AL-KO Robolinho 1150 escaped robot error?
- M
  marshallmaryAug 29, 2025
  If the AL-KO Lawn Mower has escaped, correct the location of the boundary cable around curves and obstacles, as the appliance is outside the designated grass surface.
D
Duane FoxAug 27, 2025
What to do if AL-KO Robolinho 1150 is in bad position?
- D
  Daniel MckeeAug 27, 2025
  If your AL-KO Lawn Mower is in a bad position, ensure it is placed on the designated grass surface. Correct the boundary cable's location around curves and obstacles, and eliminate any criss-crossing of the cable. This may happen because the appliance is outside the designated grass surface or the boundary cable has been routed in a criss-cross pattern.
R
Richard KingAug 26, 2025
Why is the loop signal weak on my AL-KO Robolinho 1150?
- J
  jorge62Aug 26, 2025
  If your AL-KO Lawn Mower shows a weak loop signal, check the LEDs on the base station and ensure the power source is properly connected by disconnecting and reconnecting it. If the issue persists, raise the boundary cable to the correct height, attaching it directly to the grass if needed. It might be that the boundary cable is buried too deep.
L
Laura SmithAug 25, 2025
Why does my AL-KO Lawn Mower say no loop signal?
- D
  David HintonAug 26, 2025
  If your AL-KO Lawn Mower displays a 'No loop signal' error, first check the LEDs on the base station. Then, check the power source by disconnecting and reconnecting it. Finally, inspect the boundary cable for any damage and repair it if necessary.
D
Diana AdamsAug 23, 2025
What to do if AL-KO Robolinho 1150 Lawn Mower bumper deflected?
- M
  Michelle ClarkAug 23, 2025
  If the AL-KO Lawn Mower has driven into an obstacle and cannot free itself, especially near the base station, place the appliance on the designated grass surface. Also, ensure the boundary cable is correctly positioned.

AL-KO Robolinho 1150 Specifications

General

Type	Robotic lawn mower
Cutting width	220 mm
Grass catcher	No
Product color	Gray
Number of blades	4
Number of wheels	4 wheel(s)
Rotational speed	3400 RPM
Maximum lawn area	1200 m²
Mulching function	-
Sound power level	58 dB
Sound pressure level	60 dB
Maximum cutting height	55 mm
Minimum cutting height	25 mm
Cutting clearance adjustment	Yes
International Protection (IP) code	IPX1
Power source	Battery
Battery voltage	25 V
Battery capacity	5 Ah
Battery life (min)	100 min