Allen-Bradley Kinetix 5700 Installation Instructions

Allen-Bradley Kinetix 5700

16 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Installation Instructions

Kinetix 5700 DC-bus Power Supply

Catalog Numbers 2198-P031, 2198-P070, 2198-P141, 2198-P208

About the DC-bus Power Supply

The Kinetix® 5700 DC-bus (converter) power supply with 400V-class three-phase AC input

provides continuous output power and current to servo drives for applications with requirements

in the range of 7…46 kW and 10.5…69.2 A, respectively.

See the Kinetix 5700 Servo Drives User Manual, publication 2198-UM002

, for detailed

information on wiring, applying power, troubleshooting, and integration with ControlLogix®

EtherNet/IP communication modules or CompactLogix™ 5370 controllers.

Topic Page

About the DC-bus Power Supply 1

Important User Information 2

Catalog Number Explanation 3

Before You Begin 3

Remove the Grounding Screw in Select Power Configurations 3

Install the DC-bus Power Supply 5

Drilling Hole Patterns 6

Connector Data 9

Wiring Requirements 12

Circuit Breaker/Fuse Specifications 14

Specifications 15

Additional Resources 15

Table of Contents

Other manuals for Allen-Bradley Kinetix 5700

User Manual460 pages

Reference Manual497 pages

Quick Start Guide10 pages

Questions and Answers:

K
Kayla SinghAug 18, 2025
Why is my Allen-Bradley Kinetix 5700 system unstable?
- T
  Timothy BrownAug 18, 2025
  An unstable Allen-Bradley Servo Drives system can stem from several factors. It could be due to an incorrect or open position feedback device, so check the wiring. The system might unintentionally be in Torque mode; verify the programmed primary operation mode. Motor tuning limits might be set too high, so run Tune in the Logix Designer application. Also, improper grounding or shielding techniques could be transmitting noise. Check the wiring and ground. The motor select limit might be incorrectly set, therefore check setups and run Tune in the Logix Designer application.
J
Jon ReedAug 21, 2025
Why can't I get the motor acceleration/deceleration I want with my Allen-Bradley Kinetix 5700 Servo Drives?
- W
  wilsonrebeccaAug 21, 2025
  If you're struggling to achieve the desired motor acceleration or deceleration with your Allen-Bradley Servo Drives, consider these potential causes: * Torque limits may be set too low, so verify their settings. * An incorrect motor might be selected in the configuration; select the correct motor and rerun Tune in the Logix Designer application. * The system inertia could be excessive, so check the motor size versus the application needs and review servo system sizing. * Also, an incorrect acceleration or velocity limit could be the reason, so verify the limit settings and correct them as necessary.

Allen-Bradley Kinetix 5700 Specifications

General

Series	Kinetix 5700
Category	Servo Drives
Control Method	EtherNet/IP
Protection Rating	IP20
Dimensions	Varies by model
Axis	Single and Multi-axis
Communication Protocol	EtherNet/IP, CIP Sync
Feedback Type	resolver
Operating Temperature	0 to 60 °C
Storage Temperature	-40°C to 85°C
Relative Humidity	5% to 95% non-condensing
Shock	15 g
Safety Features	Safe Torque Off (STO), Safe Stop 1 (SS1), Safe Stop 2 (SS2)
Vibration	5-500 Hz, 2g

Related product manuals

Preview: Allen-Bradley Kinetix 5500

Allen-Bradley Kinetix 5500

Preview: Kinetix 5100 2198-E1004-ERS

Kinetix 5100 2198-E1004-ERS

Kinetix 5100 2198-E1007-ERS

Kinetix 5100 2198-E1020-ERS

Preview: Allen-Bradley Kinetix 350

Allen-Bradley Kinetix 350

Preview: Allen-Bradley Kinetix 6000

Allen-Bradley Kinetix 6000

Allen-Bradley Kinetix 6500

Preview: Allen-Bradley 2097 series

Allen-Bradley 2097 series

Allen-Bradley 2094-BM03-S

Allen-Bradley 2094-BMP5-S

Preview: Allen-Bradley 2094-AC05-MP5

Allen-Bradley 2094-AC05-MP5

Allen-Bradley 2198-D032-ERS4