Ametek JOFRA ATC-125

Other manuals for Ametek JOFRA ATC-125

Questions and Answers:

A
Amber McguireAug 20, 2025
How to fix no light in display error in Ametek JOFRA ATC-125 Measuring Instruments?
- P
  pinedajohnAug 20, 2025
  If the Ametek Measuring Instruments display shows no light, begin by inspecting the fuses in the mains inlet. Then, check the fuses located on the Power PCB: F1 – F6 for ATC-125, F1 – F7 for ATC-140/155/156/157, and F1 – F7 for ATC-250/320/650. Also, check the supplies and replace the Power PCB if necessary, as a defective regulator on the Power PCB could be the cause.
J
Jared GriffinAug 22, 2025
What to do if stirring motor is not pulling stirring magnet in Ametek JOFRA ATC-125 Measuring Instruments ATC-140/250 A/B?
- C
  Christopher SmithAug 22, 2025
  To resolve the issue of the stirring motor not pulling the stirring magnet in Ametek Measuring Instruments ATC-140/250 A/B, set the stirring speed to 50. Measure the voltage across CN11 on the ATC-250 and CN13 on the ATC-140; it should be approximately 18V. If the voltage is correct, replace the motor. If there's no signal, check for a 5V signal on (ATC-140 Power PCB CN9 pin 11) or (ATC-250 Power PCB CN3 pin 11). If the 5V signal is present, replace the Power PCB; otherwise, inspect the ribbon cable and Main PCB. Also, if the stirring magnet has a flat side due to wear, replace it.
J
jeremy40Aug 30, 2025
What should I do if my Ametek JOFRA ATC-125 ATC-155 isn't cooling or heating enough?
- L
  lauraberryAug 30, 2025
  To address the issue of the calibrator not cooling or heating sufficiently (ATC-155 only) on Ametek Measuring Instruments, set the temperature to –50°C. On the power PCB, measure the voltage between CN8 terminal 1(+) and terminal 2(-) and the voltage between CN1 terminal 1(+) and terminal 2(-). If the voltage on CN1 is higher than 30V, replace the well and recalibrate the unit. If the voltage on CN8 is 0.45V ±0.01V and the calibrator does not cool down sufficiently, replace the well and recalibrate the unit. If the voltage on CN1 is less than 30V and the voltage on CN8 differs from 0.45V ±0.01V, adjust R9 until the voltage is 0.45V ±0.01V. If it is impossible to adjust the voltage on CN8, replace the Power PCB.
T
Taylor DodsonSep 1, 2025
What causes no readout in display error in Ametek JOFRA ATC-125?
- M
  Ms. Miranda Salazar MDSep 1, 2025
  If the Ametek Measuring Instruments display shows no readout, check the ribbon cable between the Main PCB and the display PCB. Also, check the ribbon cable between the display PCB and the display module, as the communication between the CPU and the display may be defective.
J
Jerry BurkeSep 6, 2025
Why are keys not functioning on my Ametek JOFRA ATC-125?
- C
  Christine JonesSep 6, 2025
  If one or more keys are not functioning on your Ametek Measuring Instruments, check the cable connection between the keyboard and the display PCB. Also, check all keys in the Service Menu, as the connection to the Main PCB may be defective.
L
littlejasonSep 9, 2025
How to fix 'Calibrator type illegal' error on Ametek JOFRA ATC-125 Measuring Instruments?
- P
  palmercodySep 9, 2025
  To resolve the "Calibrator type illegal" error message on your Ametek Measuring Instruments, check that the calibrator setting is correct on the Main PCB. Refer to section 2.3.1 in the manual for DIP Switch Setting instructions.
J
Joseph WebsterSep 12, 2025
What to do when Ametek Measuring Instruments shows 'AD-converter not responding' error?
- A
  Angelica KellerSep 12, 2025
  To address the "AD-converter not responding" error message on your Ametek Measuring Instruments, first, verify that all voltages on the power PCB are correct. If they are correct, the Main PCB is likely defective and should be replaced. If the voltages are incorrect, replace the Power PCB.
K
Kimberly LopezSep 14, 2025
How to resolve 'Slave temperature too high' error on Ametek Measuring Instruments?
- K
  Kenneth TorresSep 14, 2025
  To address the "Slave temperature too high" error message on your Ametek Measuring Instruments, after the main adjustment has stabilized, check the measuring circuit by creating a short circuit in the differential TC connection (CN16 on the input board) instead of the sensors. Then, in the Service Input Menu, verify that the Slave TC reads 0°C±0.1°C. If it reads correctly, the issue lies with the sensor. Otherwise, the Main PCB is faulty.