Anilam 6000M - Page 130

CNC Setup Utility Manual
P/N 70000490C - Index
Index-2 All rights reserved. Subject to change without notice.
10-December-04
print, 4-3
save, 4-1
utilities, description, 4-1
console switches, illustration, 1-3
continuous path range (MC_4000), 2-54
continuous path, setup parameters, table,
2-54
control software, setup parameters
description, 2-71
controller, auto-tuning
current, procedure, 5-2
frequency, procedure, 5-4
position, procedure, 5-8
velocity, procedure, 5-5
controller, tuning, test sequence, listed, 5-1
controller, velocity, fine-tuning, 5-7
copy
configuration, 4-1
restore from, 4-2
create backup program (MC_1206), 2-12
current
auto-tune display, illustration, 5-2
auto-tune, illustration, 5-3
controller auto-tuning, procedure, 5-2
tune, manual test, 5-10
current vs. distance plot
illustration, 5-14
tuning test, 5-13
cutter compensation in Draw (MC_1107), 2-6
D
damping, 5-4
data bits (MC_1353), 2-14
datum search speed, 2-60
default axis display (MC_1000), 2-2
default axis values (MC_1003), 2-2
default insert mode (MC_1202), 2-12
default output device (MC_1375), 2-14
default plane (MC_1001), 2-2
default program block mode (MC_1101), 2-5
default rapid rate, setting, 2-76
default settings, setup utility, 1-2
default spindle orientation angle (MC_5003),
2-65, 2-88
default tab width (MC_1205), 2-12
default tool type (MC_1006), 2-5
default tool-table file (MC_5014), 2-66, 2-89
default units (MC_1002), 1-6, 2-2
degrees, 1-6, 2-70
degrees per minute, 1-6, 2-70
delete backup files during optimize
(MC_1394), 2-13
diameter of spindle probe gauge (MC_1165),
2-11
diameter of tool probe gauge (MC_1161),
2-11
Direct Numeric Control. See DNC
directory for user program (MC_1305), 2-13
disclaimer, iii
disk access marker (MC_1013), 2-4
display internal interface message
(MC_5102), 2-68
display program text, (MC_1102), 2-5
display resolution (MC_4312), 2-62
display resolution, description, 2-74
display, setup, 3-3
DNC
buffer size, 2-84
buffer size (in buff. Mode) (MC_4061),
2-56, 2-84
CornerRad, 2-56
description, 2-84
drip feed mode, 2-84
execution mode, 2-84
execution mode (MC_4060), 2-56, 2-84
ignore G41/2, G59, and blueprint
(MC_4064), 2-56
macro number (MC_4063), 2-56
setup parameters, table, 2-56
tool comp, 2-56
use DNC macro at end of block
(MC_4062), 2-56
wait for start (MC_4065), 2-56, 2-85
draw mode, setup parameters, table, 2-5
draw view (MC_1108), 2-6
dry run
cancel, active mode (M107), 2-86
enable (M105), 2-86
linear feedrate, 2-85
mode, M-codes, table, 2-85
no Z (M106), 2-86
rotary feedrate, 2-61
dynamic numeric control
setup parameters, description, 2-84
E
Edit (F8), editing program from Tool Page,
2-91
edit ballscrew table (MC_3072), 2-53, 2-78,
2-80
edit, error messages, 3-1