Need help?Do you have a question about the Apache Labs ANDROMEDA ANAN-7000DLE MKII and is the answer not in the manual?
General| Voltage | 13.8 V DC |
|---|---|
| Receiver Type | Direct Sampling |
| ADC Resolution | 16-bit |
| Power Supply | External 13.8 V DC |
| Type | SDR Transceiver |
| Operating Modes | CW, SSB, FM, AM, Digital |
| Output Power | 100W |
| Interface | Ethernet, USB |
| Audio Output | Stereo |
Details the advantages and performance of the ANDROMEDA transceiver.
Explains the function and layout of the front panel touchscreen display.
Describes the functions of the dual rotary encoders on the front panel, including VFO, gain, and filters.
Covers the front panel pushbuttons, their LED indicators, and includes softkey, band, and VFO buttons.
Lists and describes the function of each rear panel connector and port.
Essential guidelines for safe and optimal operation, including ventilation and power.
Explains the radio's heat management system using heatsinks and fans.
Step-by-step guide to connect and power up the radio for initial use.
Instructions for turning on the radio and launching the Thetis software.
Explains how to select and tune VFO A or VFO B using the encoder and A/B button.
Details the process of changing radio bands using the SHIFT button and band select buttons.
Describes how to select operating modes using front panel buttons or softkey menus.
Explains adjustment of AF gain and AGC controls for RX1 and RX2.
Describes different spectrum display options like Panadapter, Waterfall, and Panafall.
Explains how to configure and view RX and TX meter settings via the display menu.
Guides on selecting antennas for RX and TX through the Thetis Setup form.
Introduces the use of softkey menus for accessing radio functions.
Lists functions available in the Quick Menu, including NR, NB, ANF, AGC, and Attenuation.
Details functions within the RX Menu, such as Diversity, Gain, Filter, and RX Mute.
Lists functions in the VFO Menu, including Band, Mode, Bandstack, and Tune Step.
Covers functions in the TX Menu, such as Mode Settings, Puresignal, and MOX.
Lists functions in the Display Menu, including RX/TX meters and display modes.
Details functions in the Audio Menu, such as recording, replay, and virtual audio channels.
Lists functions in the Setup Menu, including Duplex, TX Monitor, and Equaliser.
Describes functions in the Extended Menu, such as Test, Quick save/restore, and filter/band steps.
Guide to setting up and performing voice transmissions.
Details how to set TX drive power and adjust microphone gain.
Step-by-step process for correctly setting up microphone levels and audio path.
Explains the various methods to initiate transmit (TX) mode.
Covers performing voice transmissions, monitoring audio, and using VOX.
Details additional TX settings available on the 'mode dependent settings' form.
Guide for operating the transceiver in CW modes.
Instructions for connecting a CW key or paddle.
Steps for setting up the radio to receive CW signals, including APF.
Procedures for tuning, setting power, and transmitting in CW mode.
Explains various settings specific to CW operation within the Mode Settings form.
Details the QSK (full break-in) feature for CW operation.
Covers operating the transceiver in modes other than voice or CW.
Guide to FM operation, including channel spacing and mode settings.
Information on using digital modes with the ANDROMEDA and required PC software.
Explores advanced features for optimizing receiver performance.
Explains how to use the dual independent receivers simultaneously.
Details the use of RF attenuators to prevent ADC overload from strong signals.
Describes how to use the filter low and high cut controls to remove QRM.
Explains various noise reduction and blanking algorithms available in Thetis.
Details how to use the diversity feature for beamforming and signal enhancement.
Explains the use of RIT and XIT for independent receiver and transmitter tuning.
Describes how to enable and use split frequency operation.
Explains the Puresignal algorithm for correcting transmitter non-linearity.
Step-by-step guide to set up and calibrate the Puresignal feature.
Details how to operate with Puresignal and interpret feedback indicators.
Information on connecting an external linear amplifier for Puresignal use.
Placeholder section for Automatic Antenna Tuner information.
Overview of the Thetis Setup screen and its various configuration tabs.
Details the ANDROMEDA specific setup options within Thetis.
Guide to reconfiguring front panel controls and softkey menus.
Explains how to assign functions to rotary encoders using the Settings Editor.
Details how to assign functions to pushbuttons using the Settings Editor.
Explains how to configure indicator assignments using the Settings Editor.
Guides on editing softkey menus using the Settings Editor.
Details on connecting and testing a linear amplifier.
Explains the PTT Out feature for keying external amplifiers and testing procedures.
Notes on ALC control and setting drive levels for external amplifiers.
Describes using Open Collector Outputs for automatic band selection.
Explains how to connect a coupler for Puresignal with an external amplifier.
Guidelines for maintaining the internal Intel NUC PC, including protection and backups.
Information on setting up network connections for the radio via Wi-Fi or wired Ethernet.
Details on using the HPSDRBootloader to flash firmware.
Instructions for assigning a static IP address via the HPSDRBootloader.
Guide to using HPSDRProgrammer for Protocol 2 firmware updates.
Details the product warranty terms and conditions.
Lists external resources and documentation for further information.
To Next Page
