Need help?Do you have a question about the AudioCodes MediaPack and is the answer not in the manual?
General| Fax Support | T.38, G.711 pass-through |
|---|---|
| Humidity | 10% to 90% non-condensing |
| Model | MediaPack |
| Category | Gateway |
| Voice Channels | 2, 4, 8, 24 (depending on the specific model) |
| Network Interfaces | Ethernet (10/100/1000 Mbps) |
| Protocols | SIP, MGCP |
| Voice Codecs | G.711, G.726, G.729, iLBC |
| Management | Web-based, SNMP, CLI |
| Security | TLS, SRTP, HTTPS, SSH |
| FXS Ports | Varies by model (e.g., 8, 16, 24) |
| FXO Ports | Varies by model (e.g., 8, 16, 24) |
| Ethernet Interfaces | 10/100/1000 Mbps |
| Power Supply | AC 100-240V, 50-60Hz or DC (varies by model) |
| Dimensions | Varies by model (e.g., 1U, 2U rack mount) |
| Weight | Varies by model |
| Operating Temperature | 0°C to 45°C (32° to 113°F) |
| Storage Temperature | -40°C to 70°C (-40°F to 158°F) |
Describes MP-11x hardware installation: physical description, unpacking, mounting, and cabling.
Provides a physical description of the front and rear panels of the MP-11x series devices.
Details the MP-11x front panel, focusing on LEDs for operating statuses.
Describes the MP-11x rear panel, detailing ports for cabling and interfaces.
Outlines the procedure for unpacking the MP-11x carton and checking package contents.
Explains mounting options for MP-11x: desktop, wall, and 19-inch rack.
Details the process of mounting the MP-11x device on a desktop.
Provides instructions for wall mounting the MP-11x device.
Guides on installing the MP-11x in a 19-inch rack using a shelf.
Covers cabling MP-11x to network, FXS/FXO devices, and power.
Explains how to connect the MP-11x to the Ethernet network.
Details connecting the MP-11x to analog telephone interfaces (FXS/FXO).
Describes how to cable the FXS Lifeline feature for analog phone connection.
Guides on connecting the MP-11x RS-232 port to a PC for serial communication.
Provides instructions for connecting the MP-11x device to a power source.
Describes the hardware installation for the MP-124.
Provides a physical description of the MP-124 front and rear panels.
Details the MP-124 front panel, including LEDs and the reset button.
Describes the MP-124 rear panel, detailing ports and power configurations.
Outlines the procedure for unpacking the MP-124 carton and checking package contents.
Explains mounting options for MP-124: desktop and 19-inch rack.
Details the process of placing the MP-124 device on a desktop.
Guides on installing the MP-124 in a 19-inch rack using brackets.
Covers cabling MP-124 to grounding, Ethernet, FXS, RS-232, and power.
Discusses power surge protection and grounding requirements for the MP-124.
Explains how to connect the MP-124 to the Ethernet network.
Details connecting the MP-124 to analog FXS lines via a 50-pin Telco cable.
Guides on connecting the MP-124 RS-232 port to a PC for serial communication.
Describes connecting the MP-124 to AC and 48-VDC power supplies.
Details the cabling procedure for the MP-124 AC power supply.
Details the cabling procedure for the MP-124 DC power supply.
Explains how to change the device's default IP address to match network environment.
Guides on assigning an IP address via the device's Web interface.
Details assigning an IP address using the AudioCodes BootP/TFTP Server application.
Explains assigning an IP address using a connected telephone and voice menu.
Guides on assigning an IP address via the Command Line Interface (CLI).
Covers initial configuration of basic SIP parameters using the Web interface.
Provides an example for enabling channels and configuring Tel-to-IP call routing.
Explains how to save configuration to flash memory and reset the device.
Guides on changing Web interface login credentials for security.
Details how to save and load device configuration settings using an .ini file.
Explains how to restore the device's configuration settings to factory defaults.
Outlines how to upgrade the device using firmware and auxiliary files.
Guides on using the Software Upgrade Wizard for firmware and file loading.
Details loading .ini, Dial Plan, Call Progress Tones, etc. files.
Describes the operating status LEDs on the front panel of MP-11x and MP-124 devices.
Explains how to monitor the device using its Web interface.
Guides on accessing and viewing current alarms via the Web interface's 'Home' page.
Describes viewing voice channel status using port icons on the Web interface's 'Home' page.
To Next Page