Axis 207W - User Manual

Other manuals for Axis 207W

Questions and Answers

Q
qlucasSep 4, 2025
What to do if no MPEG-4 is displayed in the client for Axis 207W Security Camera?
- R
  Rachel CampbellSep 4, 2025
  If no MPEG-4 is displayed in the client for your Axis Security Camera, verify that the correct network interface is selected in the AMC control panel applet (network tab). Also, ensure that the relevant MPEG-4 connection methods are enabled in the AMC control panel applet (network tab). You can also select the MPEG-4 tab in the AMC control applet and click the button 'Set to default MPEG-4 decoder'.
M
Miranda PierceSep 18, 2025
What does it mean when the Status and Network LEDs are flashing red rapidly on Axis 207W?
- K
  Kristen RobertsSep 18, 2025
  If the Status and Network indicator LEDs are flashing red rapidly on your Axis Security Camera, this indicates a hardware failure. Contact your Axis dealer for assistance.
D
daniellekimSep 16, 2025
Why is the power indicator not constantly lit on my Axis Security Camera?
- S
  Stephanie EvansSep 16, 2025
  If the power indicator on your Axis Security Camera is not constantly lit, check that you are using an AXIS PS-H adapter, as a faulty power adapter could be the cause.
T
Taylor MeadowsSep 14, 2025
How to adjust image brightness on Axis 207W Security Camera?
- L
  Lawrence ValentineSep 14, 2025
  If the image from your Axis Security Camera is too dark or too light, check the video image settings.
J
Jose BlackSep 13, 2025
How to resolve lost or poor images in pre-trigger buffer on Axis Security Camera?
- J
  John SkinnerSep 13, 2025
  If you're experiencing lost or poor images in the pre-trigger buffer (MPEG-4 video stream) on your Axis Security Camera, make sure that Cyclic refresh under Setup > Video & Image > Advanced > MPEG-4 is disabled.
D
Dr. Amanda Berger DDSSep 12, 2025
What to do about a possible IP address conflict on my Axis 207W?
- J
  Jennifer GonzalezSep 12, 2025
  If there's a possible IP address conflict with another device on the same subnet for your Axis Security Camera, set the static IP address to 0.0.0.0.
R
rossanthonySep 9, 2025
Why is no multicast MPEG-4 displayed in the client for my Axis 207W?
- M
  michelle17Sep 9, 2025
  If no multicast MPEG-4 is displayed in the client for your Axis Security Camera, check with your network administrator that the multicast addresses used by the camera are valid for your network. Also, check with your network administrator to see if there is a firewall preventing viewing.
M
millerjefferySep 7, 2025
How to configure Axis 207W when ActiveX installation is restricted?
- C
  cchaneySep 7, 2025
  If the installation of an additional ActiveX component is restricted or prohibited for your Axis Security Camera, configure your camera to use a Java applet for updating the video images under Live View Config > Layout > Default Viewer for Internet Explorer.
C
Cheryl BrownSep 5, 2025
Why is the color saturation different in MPEG-4 and Motion JPEG on my Axis 207W Security Camera?
- T
  Tina MorrisSep 5, 2025
  If the color saturation differs between MPEG-4 and Motion JPEG on your Axis Security Camera, try modifying the settings for your graphics adapter.
R
Roberta LopezAug 21, 2025
Why is my Axis 207W accessible locally, but not externally?
- M
  Mr. David PerryAug 21, 2025
  If your Axis Security Camera is accessible on your local network but not externally, there are several potential causes. First, the broadband router configuration may need adjustment; enable the NAT-traversal feature to automatically configure the router for camera access. Second, your internet firewall might be blocking access, so check with your system administrator. Finally, verify if you need to configure the default router settings.

Axis 207W Specifications

General

Camera Type	Network Camera
Sensor Type	1/4" progressive scan CMOS
Resolution	640x480 (VGA)
Frame Rate	30 fps
Lens Type	Fixed
Aperture	F2.0
Field of View	54°
Video Streaming	Yes
Wireless Connectivity	802.11b/g
Security	Password protection, IP address filtering, HTTPS encryption
Compression	Motion JPEG
Protocols	HTTP, HTTPS, TCP, UDP, RTP, RTSP, SMTP, FTP
Audio Support	Two-way audio
Power Supply	5 V DC
Operating Conditions	0°C to 50°C