Bauer LINESTAR 9000 - Limits When Using an Open Conductor Loop with Asymmetrical Layout

115 pages

To Next Page

To Previous Page

Operating Manual for BAUER LINESTAR 9000 with hose feed 11

7.2.1.2 PERMISSIBLE INCLINATION

Steering antennas in middle of span

7.2.2 LIMITS WHEN USING AN OPEN CONDUCTOR LOOP WITH ASYMMETRICAL

LAYOUT

OPEN CONDUCTOR LOOP

symmetrical layout

In addition to the previously indicated limits, the following deviation tolerances must be complied with.

Main Page

Default Chapter6
- Table of Contents6
1 General Instructions9
2 Warning Symbols10
3 General11
4 General Instructions for Safety and Accident Prevention11
5 Safety Precautions for Linestar 900012
- Electrical System12
- Mechanical System12
6 Technical Description13
- Components of the Linestar 900013
  - Components of the below Ground Guidance14
- Centre Feed - End Feed16
  - Centre Feed16
  - End Feed16
7 Use of Linestar17
- General Limits17
  - Inclination17
  - Permissible Bending Angles17
- Limits with below Ground Guidance18
  - Limits When Using an Open Conductor Loop18
  - Limits When Using an Open Conductor Loop with Asymmetrical Layout19
- Track Determination and Maintenance20
  - Travel Direction20
8 Linestar Central Unit21
- Four-Wheel Main Cart21
- Two-Wheel Central Unit22
9 Control Centre23
- Control Centre Linestar Pro23
  - Standard Built-In Components24
- Control Centre Linestar Pro-G26
  - Standard Built-In Components27
10 Linear Control System28
- General28
- Specified Minimum Curve Radius29
- Furrow Guidance30
- Cable Guidance Installation and Adjustment30
- Below Ground Guidance32
  - Oscillator Box, Steering Antennas, Track Unit32
  - Below Ground Cable35
- Setting Linear Control36
  - Furrow and Cable Guidance36
  - Below Ground Guidance37
- Setting Stop Switch37
11 Diesel Generator Unit39
12 Alignment of the Linestar39
- Aligning the Central Unit Parallel to the Linear Guidance (Furrow, Cable)39
- Align Spans 90° at Right Angle to the Central Unit40
- Aligning the Central Unit to the Linear Guidance (below Ground Guidance)40
13 Alignment Control42
- Microswitch Adjustment42
14 Electrical System43
- Cables and Markings43
- Installation, Connection of Control Centre44
- Alignment Control Connection44
15 First Start-Up44
- Checking of Central Unit44
- Checking of Truss, End Tower and Overhang45
- Gearboxes and Drive Motors45
  - Gearboxes45
  - Drive Motor46
- Oscillator Box (Only with below Ground Guidance)46
- Control Centre47
  - Checking Voltage and Wiring47
  - Checking Tower Travel Direction47
- Alignment of the Towers48
- Alignment Control Adjustment48
- Checking Alignment49
- Machine Offset from Linear Guidance51
  - Alignment of the Machine with Furrow / Cable Guidance51
  - Ausrichten der Maschine mit Untergrundsteuerung52
16 Terminology54
17 Start-Up55
- Start Linestar in Operating Mode "Linear55
  - Start Linestar with Hose Feed55
- Starting after Intermediate Stop55
- Shut-Down Procedure56
  - System Shut off During Irrigation56
  - Automatic Systemm Shut off at Field End56
- Starting Linestar to Run in Opposite Direction after an Automatic Shut-Down56
- Starting the Linestar in Operating Mode "Wheel Swivelling57
- Starting the Linestar in Operating Mode "Pivoting57
- Shut down Procedure58
18 Maintenance Instructions59
- Service Intervals59
- Service Plan60
- Post-Season Maintenance62
- Pre-Season Maintenance62
  - Preload Forces and Tightening Torques of Bolts63
19 Troubleshooting64
- Restart after Doglegging65
20 Technical Data66
- Dimensions of Bauer Linestar 9000 - 2 Wheel66
- Dimensions of Bauer Linestar 9000 - 4 Wheel One Sided66
- Dimensions of Bauer Linestar 9000 - 4 Wheel Double Sided66
21 Options67
- Low Pressure Shut-Off67
- Electric Shut-Off Valve (Central Unit)67
- End Gun67
- Booster Pump for End Gun67
- Automatic Interval Control68
- Automatic „On/Off" and Interval Control68
- Tower Alignment Switch68
- Running Light68
- End Stop68
- Stop Ramp69
22 Towing of Linestar 2-Wheel69
- Towing the Linestar from Central Unit69
- Towing the Linestar at the End Tower71
- Towing the Linestar at a Freestanding Span72
23 Electrical Wiring Diagrams74
- Control Center Linestar Pro75
  - Control Center Linestar Pro - Wiring Diagram 175
  - Control Centre Linestar Pro - Infeed78
- Control Centre Linestar Pro with below Ground Guidance80
  - Control Centre Linestar Pro W. below Ground Guidance - Wiring Diagram81
  - Control Centre Linestar Pro W. below Ground Guidance - Infeed84
- Control Centre Linestar Pro-G89
  - Control Centre Linestar Pro-G - Wiring Diagram 189
  - Control Centre Linestar Pro-G - Infeed92
- Linestar Linear Control94
- Linestar Tower Box100
- Booster Pump for End Gun110
24 Service - Evidence111
25 Conformity Certificate115

Bauer LINESTAR 9000 - Limits When Using an Open Conductor Loop with Asymmetrical Layout

Table of Contents

Related product manuals